Yamaha CS1D, Service Manual

Page: 130 / 150

* W.CLK
OK
12-1. CS1D-MIO (ENGINE A1)OK
12-1. CS1D-MIO (ENGINE A1)
SI/SO: OK
W.CLK: OK
ID: OK
* SI/SO
OK
* ID
OK
* MSB/LSB
OK
*
2CH/4CH
OK
In
Out
A1 B2
Please select 68pin ports to check.
[TO CONSOLE Port]
[ENGINE Port]
OK
Connect [ENGINE A1] to [TO CONSOLE 1].
OK CANCEL
The CIO port combinations for MIO checking
are fixed, so other combinations can not be
selected.
TO CONSOLE 1 ENGINE A1
TO CONSOLE 1 ENGINE A2
TO CONSOLE 2 ENGINE B1
TO CONSOLE 2 ENGINE B2
When changing to the next port, a pop-up box like
that below is displayed, so change the connections in
order according to the instructions and check
CS1D
121
* ETHER (EIF [B])
*
ETHER (CCAS)
*
ETHER (EIF [A])
OK
* RS232C
*
USB
OK
OK
11. CS1D-Communication OK
11. CS1D-Communication
ETHER (EIF [A]): OK
ETHER (EIF [B]): OK
RS232C: OK
USB: OK
ETHER (CCAS): OK
OK
OK
CH1
CH2
CH1
CH2
CH1
CH2
* ETHER (EIF [B])
*
ETHER (CCAS)
*
ETHER (EIF [A])
NG
* RS232C
*
USB
NG
NG
11. CS1D-Communication
11. CS1D-Communication
ETHER (EIF [A]): NG
ETHER (EIF [B]): NG
RS232C: NG
USB: NG
ETHER (CCAS): NG
NG
NG
CH1
CH2
CH1
CH2
CH1
CH2
CH1
CH2 NG
NG
CH1
CH2 NG
NG
CH1
CH2
USB open error. Please check
USB-Device-Driver on HostPC.
NG
NG
NG example
Connect USBport [HostPCtoCS1D]. Push OK button.
OK
When the pop-up box asking you to make the connections
for the USB check appears, connect the USB cable.
(If you connect the cable before requested, the software is
not loaded properly.)
(The USB check driver must be installed before hand.)
11. CS1D Communication Test
This test checks communications for the BIF1, 2, CCAS boards etc.
12-1. CS1D-MIO
(ENGINE A1) Test
This test checks the MIO (Engine
A1 port).
Check item
SI/SO
W.CLK
ID
MSB/LSB
2CH/4CH
MSB/LSB
2CH/4CH
MSB/LSB
2CH/4CH
• In
• Out
12-2. CS1D-MIO
(ENGINE A2) Test
This test checks the MIO (Engine
A2 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
12-3. CS1D-MIO
(ENGINE B1) Test
This test checks the MIO (Engine
B1 port).
Check item
SI/SO
W.CLK
ID
MSB/LSB
2CH/4CH
• In
• Out
12-4. CS1D-MIO
(ENGINE B2) Test
This test checks the MIO (Engine
B2 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
12. CS1D-MIO Test
This test checks the MIO board. It checks the items
below.
Here it is assumed that the elements around the DSP
on the MTCPU board and the CIO board are
operating normally. If this can not be assumed and
an NG appears for these items, it is necessary to
consider the possibility of abnormality in the MIO
board, the CIO board, and the MTCPU board.
The detailed screen output specifications are given
on the following pages.
* There are the following restrictions on the
combination of TO CONSOLE terminal
(inspection reference terminal) and ENGINE
terminal (inspected terminal).
TO CONSOLE 1 – ENGINE A1 or ENGINE A2
TO CONSOLE 2 – ENGINE B1 or ENGINE B2
Other combinations
can not be selected.
ID change jig DIP switch
setting display
12-1.CS1D-MIO (Engine A1) Test
This test checks the MIO (Engine A1 port).
NG sample
Please refer to page 111 for NG chart.