Yamaha CRW4260t-B Page 23 User Manual Download

Page: 23 / 26

Troubleshooting

If CRW4260t is not performing as expected, look up the symptoms in the following table,
and take the appropriate corrective action.

Symptoms

Corrective action

The power to the CRW4260t is off

• Check the DC power cable connection.

The power to the computer is off

• Check to see if the SCSI card is correctly installed.

The CRW4260t is not recognized by
the computer

• Check the SCSI cable connection.

• Make sure that SCSI ID numbers are assigned

exclusively.

• Make sure that the last device in the SCSI daisy

chain is terminated correctly.

The CRW4260t does not operate
correctly

• Install the SCSI driver software again.

The disc tray will not open

• Make sure that the power to the drive is turned on.

The disc ejects

• Make sure that the disc is seated in the tray cor-

rectly.

Incorrect operation

• Make sure that the disc is seated in the tray cor-

rectly.

• Make sure that you are using the correct disc.

• Make sure that there is no dust, dirt, or conden-

sation on the disc or tray.

Summary of Contents for CRW4260t-B



























Search results

Summary of Contents for CRW4260t-B

Reviews:

Related manuals for CRW4260t-B

Brands by name

Popular brands

Yamaha CRW4260t-B, User Manual

Search results

Summary of Contents for CRW4260t-B

Reviews:

Related manuals for CRW4260t-B

Brands by name

Popular brands