manualshive.com logo in svg

Yamaha Clavinova CLP-955, Service Manual

Share
Download
Yamaha Clavinova CLP-955 Service Manual Download Page 22

CLP-955

30

■

 TEST PROGRAM

1. Measuring Condition

The following measuring instruments/ jigs are required for testing the main unit.

Measuring instruments : Level meter (IHF-C curve)

: Frequency counter

NOTE 1: Input impedance should be 1M or more. 
NOTE 2: Unless otherwise specified, connect 33 ohm load using a stereo plug and measure at 
PHONES terminal.

Setting controls

MASTER VOLUME: Maximum
Tone

: PIANO 1

Pedal

: OFF

Reverb

: OFF

AUX IN, AUX OUT

: Insert measuring plugs into all terminals.  (10K ohm load) 

Headphone terminal : Insert a measuring plug into either of the systems only.  (33 ohm load for both L/R ch.) 

2. Starting Test Program

While holding down the keyboards [C2#], [F2] and [G2#], turn on the POWER switch.

3. Carrying On Test

1. When the test program is started, “TST” is indicated on the LED display.
2. Select a test program item by pressing the [Tempo 

▲

/

▼

] button.

3. Pressing the [Start/Stop] button gets the test started.
4. If the test result is OK, “PAS” is displayed.
5. Pressing the [Start/Stop] button again, the display returns to the item selection.
6. In case of NG, “nG” is displayed.
7. If the DEMO button is pressed in this case, the display returns to the item selection. 

List of the test program

No.

LED display (Initial)

Test functions and judgement criteria

1

T01:Version  Displays

ROM version.
Displays ROM (P0.1,W0.1) versions alternately.
(P0.1 = PROGRAM Ver.0.1, W0.1=WAVE Ver.0.1)

2

T02:ROM Check1

Checks ROM.
Checks all ROMs connected to CPU’s bus.
Checks that “PAS” is displayed.

3

T03:RAM Check1

Check RAM.
Checks all RAMs connected to CPU’s bus.
Checks that “PAS” is displayed.

4

T04:WAVE ROM Check1

Checks ROM.
Checks WAVE ROM.Checks that “PAS” is displayed.

11

T11:TG1 Check

Checks sound source 1.  (Auto scale)
Produces sine waves from a low tone in sequence while switching over 
sound source tones in order.Checks that there are no excessive or 
abnormal noises.  When auto scaling is finished, sounds are produced by playing 
the keyboard.  (Monotone, first-come priority)  Pressing the tone switch produces 
sounds by that tone.

12

T12:TG2 Check

Checks sound  source 2.  (Auto scale)
Produces sine waves from a low tone in sequence while switching over 
sound source tones in order.Checks that there are no excessive or 
abnormal noises.  When auto scaling is finished, sounds are produced by playing 
the keyboard.  (Monotone, first-come priority)  Pressing the tone switch produces 
sounds by that tone.

Summary of Contents for Clavinova CLP-955


























Reviews:

No comments

Brands by name

Popular brands

Load more brands