manualshive.com logo in svg

Yamaha BANSHEE YFZ350Y, Owner'S Manual, Page: 27 / 142

Share
Download
Yamaha BANSHEE YFZ350Y Owner'S Manual Download Page 27

 

4-5

 

1

2

3

4

5

6

7

8

9

10

11

 

EBU18411

 

Brake lever 

 

The brake lever is located at the right handlebar
grip. To apply the front brake, pull the brake lever
toward the handlebar grip.

 

EBU18432

 

Brake pedal 

 

The brake pedal is located on the right side of the
ATV. To apply the rear brake, push down on the
brake pedal.

 

EBU18500

 

Parking brake 

 

Use the parking brake before starting the engine or
parking the ATV, especially on a slope. Squeeze
the clutch lever while pushing the button, then
push in the lock plate to apply the parking brake.
Squeeze the clutch lever to release the parking
brake.

TIP

 

When the parking brake is used, engine speed is
limited to 2300 r/min. Be sure the parking brake is
released before moving the throttle lever. Other-

 

1. Brake lever

1

 

1. Brake pedal

1

Summary of Contents for BANSHEE YFZ350Y















































































































































Reviews:

No comments