manualshive.com logo in svg

Yamaha BANSHEE YFZ350Y, Owner'S Manual, Page: 116 / 142

Share
Download
Yamaha BANSHEE YFZ350Y Owner'S Manual Download Page 116

 

8-41

 

1

2

3

4

5

6

7

8

9

10

11

 

3. Loosen the locknut on each side of the swing-

arm. To tighten the drive chain, turn the ad-
justing bolts in direction (a). To loosen the
drive chain, turn the adjusting bolts in direction
(b) and push the wheels forward. Turn each
adjusting bolt exactly the same amount to
maintain correct axle alignment.

TIP

 

There are alignment marks on each side of the
swingarm and on the wheel hubs. Use them to

 

check for proper wheel axle alignment.

NOTICE

 

ECB00541 

 

Improper drive chain slack will overload the en-
gine as well as other vital parts of the ATV and
can lead to drive chain slippage or breakage.
To prevent this from occurring, keep the drive

 

chain slack within the specified limits.

 

4. Tighten the locknuts and the axle holding nuts

to the specified torques.

 

1.  Axle holding nut (upper)
2.  Axle holding nut (lower)

1

2

 

1. Locknut
2.  Drive chain slack adjusting bolt
3. Alignment marks

1

2

3

Summary of Contents for BANSHEE YFZ350Y















































































































































Reviews:

No comments