Yamaha AX-492, AX-592, AX-892 Owner'S Manual Download Page 21

Page: 21 / 24

English

SPECIFICATIONS (AX-492)

AUDIO SECTION
Minimum RMS Output Power per Channel

8 ohms, 20 Hz to 20 kHz, 0.019% THD

...................................................85W+85W

6 ohms, 20 Hz to 20 kHz, 0.038% THD

...............................................100W+100W

Dynamic Power per Channel
(by IHF Dynamic Headroom measuring
method)

8/6/4/2 ohms ...................130/150/185/220W

DIN Standard Output Power per Channel

[Europe model only]

(4 ohms, 1 kHz, 0.7% THD) ..............120W

IEC Power [Europe model only]

(8 ohms, 1 kHz, 0.019% THD) .............100W

Power Band Width

8 ohms, 42.5W, 0.038% THD

.............................................10 Hz to 50 kHz

Damping Factor SP-A

8 ohms, 20 Hz–20 kHz ..............240 or more

Maximum Output Power (EIAJ)

[General model only]

8 ohms, 1 kHz, 10% THD .................130W
6 ohms, 1 kHz, 10% THD .................150W

Input Sensitivity/Impedance

PHONO ............................2.5 mV/47 k-ohms
CD/TUNER/TAPE/AUX ....150 mV/47 k-ohms

Maximum Input Signal (1 kHz, 0.003% THD)

PHONO.............................................115 mV

Output Level/Impedance

REC OUT .......................150 mV/0.6 k-ohms

Headphone Jack Rated Output/ Impedance

Output Level (8 ohms, 0.019% THD)

...............................................................0.3V

Impedance.....................................680 ohms

Frequency Response (20 Hz to 20 kHz)

CD/TUNER/TAPE/AUX ....................0±0.5 dB

RIAA Equalization Deviation

PHONO...........................................0±0.3 dB

Total Harmonic Distortion (20 Hz to 20 kHz)

PHONO to REC OUT (3V) ................0.003%
CD/TUNER/TAPE/AUX to SP OUT
(42.5W/8 ohms) ................................0.008%

Signal-to-Noise Ratio (IHF-A Network)

PHONO (5 mV Input Shorted) ............ 88 dB
CD (CD DIRECT AMP ON, Shorted)... 110 dB

Residual Noise (IHF-A Network)

CD (CD DIRECT AMP ON) ...................35

PURE DIRECT ON ..............................90

Channel Separation

CD/TUNER/TAPE/AUX (Input 5.1 k-ohms
Terminated 1 kHz/10 kHz).........65 dB/50 dB

Tone Control Characteristics

BASS:

Boost/cut ................±10 dB (20 Hz)

Turnover Frequency.........(350 Hz)

TREBLE:

Boost/cut...........±10 dB (20 kHz)

Turnover Frequency.....(3.5 kHz)

Continuous Loudness Control

Attenuation ............................–30 dB (1 kHz)

(Level related equalization)

Gain Tracking Error (0 to –60 dB) ............2 dB

GENERAL
Power Supply

[Europe and U.K. models] ...AC 230V, 50 Hz
[General model]

..................AC 110/120/220/240V, 60/50 Hz

Power Consumption ...............................210W

AC Outlets

[Europe and General models]

3 SWITCHED OUTLETS ..100W max. total

[U.K. model]

1 SWITCHED OUTLET ....100W max. total

Dimensions (W x H x D)

......................................435 x 151 x 391 mm

(17-1/8” x 6.0” x 15-3/8”)

Weight .............................9.6 kg (21 lbs. 1 oz.)

Accessories ...........Remote control transmitter

Batteries

Specifications subject to change without
notice.

Summary of Contents for AX-492, AX-592, AX-892

























Search results

Summary of Contents for AX-492, AX-592, AX-892

Reviews:

Related manuals for AX-492, AX-592, AX-892

Brands by name

Popular brands

Yamaha AX-492, AX-592, AX-892, Owner'S Manual

Search results

Summary of Contents for AX-492, AX-592, AX-892

Reviews:

Related manuals for AX-492, AX-592, AX-892

Brands by name

Popular brands