Yamaha 90A Owner'S Manual Download Page 54

Page: 54 / 82

Operation

4. Models equipped with trim rods: Once

the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Make sure that the

trim rods retracts completely during
mooring. This protects the rods from
marine growth and corrosion, which
could damage the power trim and tilt
mechanism.

[ECM00252]

EMU33121

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2. Release the tilt support lever.

3. Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

ZMU03115

ZMU03874

ZMU03875

ZMU01936

ZMU03876

6H1-9-2A-1E0.book 48 ページ２０１０年２月１７日　水曜日　午前１０時４２分

Summary of Contents for 90A



















































































Search results

Summary of Contents for 90A

Reviews:

Brands by name

Popular brands

Yamaha 90A, Owner'S Manual

Search results

Summary of Contents for 90A

Reviews:

Brands by name

Popular brands