Yamaha 9.9F Page 29 Owner'S Manual Download | Manualshive

Page: 29 / 62

background image

Operation

24

EMU27120

Oil

●

Check to be sure you have plenty of oil for
your trip.

EMU27141

Engine

●

Check the engine and engine mounting.

●

Look for loose or damaged fasteners.

●

Check the propeller for damage.

EMU36954

Install top cowling

1.

Be sure that the cowling lock lever is re-
leased.

2.

Be sure that the rubber seal is seated all
the way around the top cowling.

3.

Place the top cowling on the bottom cowl-
ing.

4.

Check to be sure the rubber seal is seat-
ed correctly between the top cowling and
the bottom cowling.

5.

Move the lever to lock the cowling as
shown.

NOTICE:

If the top cowling is

not installed correctly, water spray un-
der the top cowling can damage the
engine, or the top cowling can blow off
at high speeds.

[ECM01991]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

EMU27234

Filling fuel and engine oil

EMU27248

Filling fuel for portable tank

WARNING

EWM01830

●

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

●

Gasoline is poisonous and can cause in-
jury or death. Handle gasoline with care.
Never siphon gasoline by mouth. If you
should swallow some gasoline or inhale
a lot of gasoline vapor, or get some gas-
oline in your eyes, see your doctor im-
mediately. If gasoline spills on your
skin, wash with soap and water. If gaso-
line spills on your clothing, change your
clothes.

1.

Be sure the engine is stopped.

2.

Disconnect the fuel line from the fuel tank
and tighten the air vent screw on the fuel
tank cap.

3. Engine shut-off switch

ZMU06117

U63V2DE0.book Page 24 Monday, February 22, 2010 9:00 AM

«
...
27
28
29
30
31
...
»

Summary of Contents for 9.9F































































Reviews:

No comments

Related manuals for 9.9F

Brand: ICP Pages: 50

Brand: Alcad Pages: 98

Brand: MSI Pages: 94

Brand: JETWAY Pages: 48

Brand: Supero Pages: 92

Brand: TOHATSU Pages: 7

Brand: J&W Pages: 40

Brand: IBASE Technology Pages: 84

Brand: JETWAY Pages: 44

B85-IE35 Series

Brand: MSI Pages: 190

Brand: Advantech Pages: 90

Brand: IBASE Technology Pages: 64

B85M-P32 series

Brand: MSI Pages: 186

CONROE1333-ESATA2

Brand: ASROCK Pages: 226

Brand: Gigabyte Pages: 76

Brand: Avalue Technology Pages: 71

Brand: Supero Pages: 143

Brand: ASROCK Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands