Yamaha 9.9F Page 16 Owner'S Manual Download | Manualshive

Page: 16 / 62

background image

Specifications and requirements

11

EMU36330

Anti-fouling paint

A clean hull improves boat performance. The
boat bottom should be kept as clean of marine
growth as possible. If necessary, the boat bot-
tom can be coated with an anti-fouling paint
approved for your area to inhibit marine
growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.

EMU36341

Motor disposal requirements

Never illegally discard (dump) the motor.
Yamaha recommends consulting the dealer
about discarding the motor.

EMU36352

Emergency equipment

Keep the following items onboard in case
there is trouble with the outboard motor.

●

A tool kit with assorted screwdrivers, pliers,
wrenches (including metric sizes), and
electrical tape.

●

Waterproof flashlight with extra batteries.

●

An extra engine shut-off cord (lanyard) with
clip.

●

Spare parts, such as an extra set of spark
plugs.

Consult your Yamaha dealer for details.

U63V2DE0.book Page 11 Monday, February 22, 2010 9:00 AM

«
...
14
15
16
17
18
...
»

Summary of Contents for 9.9F































































Reviews:

No comments

Related manuals for 9.9F

Brand: u-blox Pages: 2

Brand: Supermicro Pages: 2

Brand: ECS Pages: 93

Brand: Texas Instruments Pages: 13

Brand: Gigabyte Pages: 96

Brand: IBASE Technology Pages: 81

Brand: Vector Pages: 73

Brand: Microchip Technology Pages: 35

Brand: Texas Instruments Pages: 19

dsPICDEM MCHV-3

Brand: Microchip Technology Pages: 68

Brand: AOpen Pages: 8

Brand: ASROCK Pages: 38

Voltage Supervisor SOT23

Brand: Microchip Technology Pages: 28

Brand: Gigabyte Pages: 44

Brand: Norco Pages: 55

Brand: SOYO Pages: 44

Brand: Motorola Pages: 57

PATX3070 Series

Brand: Motorola Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands