Yamaha 4UF8MD40 Owner'S Manual Download | Manualshive

Page: 33 / 54

background image

28

Fuses

Fuses protect the snowmobile electrical

system from overloading. If electrical

parts in the snowmobile are not working,

the system may have been overloaded and

caused a blown fuse. Before repairing or

replacing any electrical part, check the

appropriate fuses. If a fuse blows (opens a

circuit), all the parts of the snowmobile

that use that circuit will not work.
Once which fuse to check has been deter-

mined, perform the following steps:

1. Remove both access panels and the

hood. Locate the fuse block in front

of the engine.

YM146A



NOTE: There are spare fuses

beneath the fuse block cover.

2. Remove the suspected fuse.



NOTE: Fuse function descriptions

are next to the fuse contacts in the
fuse block.

3. Look through the clear side of the

fuse to see if the element inside is

burned or separated. If it is, the fuse is

blown and should be replaced with a

fuse of the correct amperage rating.

4. Install the fuse block cover and

install the hood and access panels.

Even after replacing a fuse, it may con-

tinue to blow if the cause of the overload

is not determined. If the fuse continues to

blow, take the snowmobile to an autho-

rized Yamaha Snowmobile dealer for ser-

vice. If not under warranty, this service is

at the discretion and expense of the

snowmobile owner.

Brake System

Yamaha recommends that the brake sys-

tem (brake lever, fluid reservoir, hose,

caliper, pads, and brake disc) be checked

daily for fluid leakage, wear, or damage

and for proper operation. Also, the brake

fluid level must be checked every time

before starting the engine.

Checking/Adding Brake Fluid

1. With the brake fluid reservoir in a

level position and the cover

removed, check the fluid level. The

brake fluid level must be at the high

brake fluid mark in the reservoir.

745-817A

WARNING

Always replace a fuse with one hav-
ing the same specified amperage
rating. Using a fuse with a higher
rating can cause severe wire dam-
age and could start a fire.

WARNING

DO NOT operate the snowmobile
when the brake lever lock is
engaged or when any component in
the brake system is damaged,
worn, or adjusted improperly. If the
snowmobile is operated and the
brake system is not functioning
properly, severe personal injury
could result.

High Brake Fluid Mark

Low Brake Fluid Mark

U8KCS1E0.book Page 28 Tuesday, May 16, 2017 5:42 PM

«
...
31
32
33
34
35
...
»

Summary of Contents for 4UF8MD40























































Reviews:

No comments

Related manuals for 4UF8MD40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands