Yamaha 2008 YZF-R1X Owner'S Manual Download

Page: 66 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

EAU42960

Replacing the air filter element

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the rider seat. (See page

3-18.)

2. Remove panels A and B. (See

page 6-7.)

3. Remove the fuel tank bolts.

4. Lift the front of the fuel tank, and

then tilt it back and away from the
air filter case. (Do not disconnect
the fuel hoses!)

WARNING

EWA10410

●

Make sure that the fuel tank is
well supported.

●

Do not tilt or pull the fuel tank
too much, otherwise the fuel
hoses may come loose, which
could cause fuel leakage.

5. Remove the air filter case cover by

removing the screws.

CAUTION:

ECA12880

When removing the air filter case
cover, be careful not to allow foreign
objects to drop into the air intake
manifold.

6. Pull the air filter element out.

1. Bolt

1. Screw
2. Air filter case cover

U4C821E0.book Page 17 Tuesday, July 17, 2007 11:37 AM

Summary of Contents for 2008 YZF-R1X













































































































Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands

Yamaha 2008 YZF-R1X, Owner'S Manual

Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands