background image

SERVICE INFORMATION

GT-222ES, SRM-222ES

F226S, T226S, C226S

8

2-3 Adjusting carburettor

SRM-222ES, T226S, C226S: Remove shield and 
cut trimmer head line lengths to 180 mm.

GT-222ES, F226S: Cut trimmer head line lengths 
to 130 mm with shield. (normal lengths : 145 mm 
cut by shield knife.)

1.  Start and warm engine for 3 minute alternating 
engine speed between WOT for 50 seconds and 
idle for 10 seconds.

2.  Adjust Idle mixture needle (A) to reach maxi-
mum idle speed using 2.5 mm blade screwdriver.

3.  Set Idle speed to 3,700 r/min by turning Idle 
adjust screw (D). Engine speed should be stable at 
3,700 +/- 50 r/min.

4.  Turn Idle mixture needle anticlockwise to reduce 
engine idle speed 1,400 r/min to set idle speed at 2,300 
r/min. The idle speed range is 2,200 - 2,400 r/min.

5. Turn Idle adjust screw (D) clockwise to increase 
idle engine speed to set idle at 3,000 r/min. The 
idle speed range is 2,900 to 3,100 r/min.

NOTE :

  Engine speed must be allowed to stabilize a 

minimum of 20 seconds after each adjustment of idle 
mixture needle to assure accurate tachometer readings.

6.  Adjust Hi speed mixture needle (B) to reach maximum 
WOT engine speed.(max. approx. 8,000 r/min) Then turn 
Hi speed mixture needle (B) anticlockwise to reduce WOT 
engine speed 20 r/min (RANG : 10-30 r/min).

NOTE :

 Nylon line length should be 180 mm with-

out shield on SRM-222ES, T226S and C226S.

 

 

Nylon line length should be 130 mm with 

shield on GT-222ES and F226S.

7. SRM-222ES(L), T226S : Stop engine and rein-
stall shield with knife, and restart engine and verify 
engine idle speed ranges from 2,600 to 3,400       
r/min, and expand and cut nylon line by shield 
knife and WOT engine speed ranges from 9,000 to 
10,000 r/min on SRM-222ES(L) and T226S, from 
6,700 to 7,700 r/min on GT-222ES and F226S.

NOTE:

 Nylon line length should be 145 mm with shield.

SRM-222ES(U), C226S : Stop engine and reinstall 
shield for 3-tooth blade (230 mm) and the blade. 
Restart engine and verify engine idle speed ranges 
from 2,600 to 3,400 r/min, and WOT engine speed 
ranges from 10,500 to 11,500 r/min.

Make sure the nylon line cutter does not rotate when engine is at idle. Engine should start and accelerate smoothly.

8. After adjusting carburettor, insert and secure new plug(s) (E) P005-001270 deep in the needle holes 
per the Emission Directive using limiter plug tool 91020 (C).

NOTE : 

WOT, and idle speed in field operation may vary from final adjustment specifications due to 

changing ambient conditions, fuel, and engine loads. Safe engine speed variances should be within the 
WOT and Idle speed ranges listed in Section 1-2, otherwise the carburettor should be readjusted.

(C)

(E)

(A)

(D)

(C)

(B)

Nylon line lengths

Model name

SRM-222ES(L) SRM-222ES(U)

GT-222ES

T226S

C226S

F226S

Carburettor 
setting

180 mm

180 mm

130 mm

Con

fi

 rming

145 mm

-

145 mm

(E)

Summary of Contents for Echo SRM-222ES









Reviews: