manualshive.com logo in svg

Yale HSA3800, Installation, Programming, Operating, Page: 27 / 28

Share
Download
Yale HSA3800 Installation, Programming, Operating Download Page 27

27

Specifications

All devices

EMC

Tested to EN 300 220-1 and ETS

300 683

Environmental conditions

-10°C to 40°C, relative humidity

70% non-condensing for all units
except the external siren. Siren: -20°C
to 50°C, relative humidity 95% non-
condensing

Radio operational range

30m in a typical domestic

installation

Can vary depending on building

construction and RF environment.

Housings 

ABS

Control unit

Keys

▼

Scrolls display downwards

▲

Scrolls display upwards

c

Program button, telephone
dialler

b

Phone number pause

a

When in programming
mode, clears the screen or
return to previous menu;
back space for telephone
numbers

Device codes

DC

Door/window contact

PIR

PIR movement detector

SD

Smoke detector

RC

Keyfob remote control

KP

Keypad remote control

WTR Help watch

Control unit illumination

Display is back lit

when the unit is mains powered.

Housing 

ABS

Siren Output 

95dBA sound pressure @

1m minimum

Zones 

20 radio devices

Radio system 

433.92MHz AM Integral

transmitter and super heterodyne
receiver with jamming detection

Power supply 

Plug top adaptor type, input

230VAC 50Hz, output 9VDC, 500ma,
tested to EN 60 950

Rechargeable battery 

Nickel cadmium

7.2V, 600mah, charge time 72h,
standby duration 8h

Telephone interface 

Tested to TBR 21.

Hands free vox operated, 6
programmable numbers with 4
different pre-recorded messages
REN rating 1

Siren

Siren output 

104dBA sound pressure @

1m minimum

Radio 

433.92MHz AM super heterodyne

receiver with jamming detection 

Power supply 

6V, 4 x D alkaline cells. 3

years minimum typical service life 

PIR movement detector

Alarm processing 

Microprocessor

controlled dual edge sequential pulse
count with pulse length discrimination

Radio 

433.92MHz AM transmitter 

Power supply 

4.5V, 3 x AA alkaline cells.

3 years minimum typical domestic
service life, 1-minute sleep timer 

Movement detection range 

15m, 110°

Door/window contact

Radio 

Microprocessor controlled

433.92MHz AM transmitter 

Power supply 

3V, 2 x AAA alkaline cells. 3

years minimum typical domestic
service life @ 50 activations a day

Smoke detector

Radio 

Microprocessor controlled

433.92MHz AM transmitter 

Power supply 

6V, 4 x AAA alkaline cells. 3

years minimum typical domestic
service life

Keyfob remote control

Radio 

Microprocessor controlled

433.92MHz AM transmitter 

Power supply 

12V 23A/MN21 alkaline

miniature "lighter" battery. 3 years
minimum typical domestic service life 

Keypad remote control

Radio 

Microprocessor controlled

433.92MHz AM transmitter 

Power supply 

9V alkaline PP3. 3 years

minimum typical domestic service life

Help button

EMC

Tested to EN 300 220-1 and ETS

300 683

Environmental conditions 

-10°C to

40°C, relative humidity 70% non-
condensing

Radio operational range 

30m in a

typical domestic installation. Can vary
depending on building construction and
RF environment

Radio 

Microprocessor controlled

433.92MHz AM transmitter

Power supply 

12V 23A/MN21 alkaline

miniature “lighter battery”. 3 years
typical domestic service life

Model:

HSA3800

HSA3020

HSA3060

HSA3010

HSA3050

HSA3045

HSA3080

HSA3030

HSA3070

Downloaded from www.ukpanels.com

Summary of Contents for HSA3800





























Reviews:

No comments