background image

6100001659-Rev1

1/9

 

• 

Please read instructions carefully before installation.

• 

Check the contents of kit. Contact your YAKIMA dealer if any parts appear missing or damaged.

• 

Clean your roof thoroughly prior to fi tting the LOCKN’LOAD Gutter Mount Heavy Duty Roof Rack System.

• 

Place these instructions in the vehicle’s glove box after installation is complete.

FIRST TIME INSTALLATION

1

2

KIT CONTENTS

ITEM COMPONENT

QTY

ITEM COMPONENT

QTY

1.

End Cap

x2

9.

Locking Clip Base

x2

2.

Rubber Skirt

x2

10.

Locking Clip

x2

3.

Nut Plate

x2

11.

Tamper Proof Torx Key

x1

4.

Leg Cover

x2

12.

Tamper Proof Torx Button Head Screw x4

5.

Washer M8

x4

13.

Spring Washer M6

x4

6.

Hex Bolt M8

x4

14.

Washer M6

x4

7.

Gutter Mount Leg 110/150/210mm

x2

15.

Mount Plate

x2

8.

Yakima Key Set

x1

16.

Rubber Foot Grip

x2

MAX VEHICLE ROOF LOAD RATING: 100KG (2 Leg Pairs) 150KG (3 Leg Pairs)

TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCES CARGO

GUTTER MOUNT HEAVY DUTY ROOF RACK ATTACHMENT SYSTEM

LOCKN’LOAD 

GUTTER MOUNT KIT

TM

®

3

NOTE 

- 110mm Leg shown

NOTE 

- 2x Gutter Mount 

150mm Leg Pack shown

4

5

6

7

8

9

10

11

12

13

14

15

16

•    Tape Measure
•    Scissors
•    #2 Phillips Head Screwdriver
•    Rubber Mallet (Optional)
•    13mm Socket Wrench

TOOLS REQUIRED:

BAR COMPONENTS SOLD SEPARATELY

Summary of Contents for LOCKN'LOAD 8000350










Reviews: