background image

HullRaiser AERO

1033518D-1/15

      

IMPORTANT WARNING

IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER  

ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO 

OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE  ATTACHMENTS PRIOR 

TO USE, AND PERIODICALLY INSPECTING  THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ 

AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION 

OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE 

AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A 

PROFESSIONAL INSTALLER SUCH AS A QUALIFIED GARAGE OR AUTO BODY SHOP.

(HullRaiseR aeRO)

MiniMuM Crossbar spread 24” (61CM)

plug 16x

base paD 2x

bRacket  2x

bail 2x

t-bOlt 2x

caRRiage bOlt 2x

stRap 2x

knOb 4x

lOng t-bOlt 2x

lOng caRRiage bOlt  2x

FITs ROuNd, squARe, 

ANd  FACTORY-INsTAlled  

AeRO bARs: 

To verify compatibility,

go online to www.yakima.com or 

call (888) 925-4621

buckle 2x

steel Hook 2x

plain strap 2x

plastic tube 2x

BOW STERN 

TIE DOWN

part #1033518 Rev.D

Summary of Contents for 1033518
















Reviews: