background image

VX-8DR/DE O

PERATING

 M

ANUAL

49

A special one-touch “HOME” channel is available for each operating band, to allow quick
recall of a favorite operating frequency on each band.

H

OME

 C

HANNEL

 R

ECALL

1.

Press the 

 key, then press the 

 key to recall the Home

Channel on the band group where you are currently operat-
ing.

2.

Press the 

 key, then press the 

 key again to return to

the previously-used frequency (either a VFO or a memory channel).

The transceiver switches to VFO mode if the 

DIAL

 knob is turned.

You may disable the above function (automatically switching to the VFO mode)
using Set Mode Item 38: HOME VFO.

H

OME

 C

HANNEL

 F

REQUENCY

 C

HANGE

The factory defaults for the Home channels are listed below. You may re-program the
Home channel in a manner identical to that used for the regular memories:

1.

Select the desired frequency, while operating in the VFO mode. Be sure to set up any
desired CTCSS or DCS tones, as well as any desired repeater offset. The power level
may also be set at this time, if you wish to store it.

2.

Press and hold in the 

 key for 1/2 second.

3.

While the memory channel number is blinking, just press the 

 key. The frequency

and other data (if any) will now be stored in the special HOME channel register.

4.

You may repeat this process on the other operating bands.

Note that the
U H F   H O M E
channel is the

one used during “Emer-
gency” operation. See
page 107 for details re-
garding this feature.

M

EMORY

 M

ODE

 

(

R

EGULAR

 M

EMORY

 C

HANNEL

 O

PERATION

)

HOME C

HANNEL

 M

EMORY

D

EFAULT

 H

OME

 C

HANNELS

O

PERATING

 B

AND

[

B

AND

 N

UMBER

]

SW Band

[1]

50 MHz Ham Band

[2]

Air Band

[3]

144 MHz Ham Band [4]
VHF-TV Band

[5]

Information Band 1

[6]

430 MHz Ham Band [7]
UHF-TV Band

[8]

Information Band 2

[9]

AM Broadcast Band [A]
FM Broadcast Band

[F]

EXP/EU V

ERSION

1.800 MHz

30.000 MHz

108.000 MHz
144.000 MHz
174.000 MHz
222.000 MHz
430.000 MHz
470.000 MHz
860.000 MHz

0.540 MHz

EXP: 76.000 MHz

EU: 88.000 MHz

USA V

ERSION

1.800 MHz

30.000 MHz

108.000 MHz
146.520 MHz
174.000 MHz
222.000 MHz
446.000 MHz
470.000 MHz
860.000 MHz

0.540 MHz

76.000 MHz

F

REQUENCY

Summary of Contents for VX-8DE





















































































































































































Reviews: