Yaesu VX-8DE Operating Manual Download

Page: 163 / 180

VX-8DR/DE O

PERATING

ANUAL

161

ODE

TEM

106: VFO SKIP

Function

: Set the My Band.

Available Values

: ON/OFF

Default

: OFF

The “My Band” feature allows you to select several operating bands, and make only those
bands available for selection via the

key.

ON: Only the bands that are turned on will be shown when pushing the

key.

OFF: When the

key is pressed, the bands that are turned “OFF” will not be shown.

See page 100 for details.

ODE

TEM

107: VOLUME MODE

Function

: Select the

key function.

Available Values

: NORMAL / AUTO BACK

Default

: NORMAL

NORMAL:

The

key keeps the status while pressing the

key.

AUTO BACK: The

key keeps the status for approximately three seconds after press-

ing the

key.

ODE

TEM

108: VOX

Function

: Enables/Disables VOX operation; sets VOX sensitivity.

Available Values

: OFF / HIGH / LOW

Default

: OFF

ODE

TEM

109: VOX DELAY

Function

: Selects the VOX delay (“hang”) time.

Available Values

: 0.5sec / 1.0sec / 1.5sec / 2.0sec / 2.5sec / 3.0sec

Default

: 0.5sec

ODE

TEM

110: WAVE MONITOR

Function

: Selects the Wave-Form function while displaying the Wave-Form via Set Mode

Item 85: SENSOR DISPLAY.

Available Values

: ALL / RX SIGNAL / TX MODULATION

Default

: OFF

ALL:

Displays the RX Audio wave form and TX Audio modulation wave
form.

RX SIGNAL:

Displays the RX Audio wave form.

TX MODULATION: Displays the TX Audio modulation wave form.

ODE

TEM

111: WX ALERT

Function

: Enables/disables the Weather Alert Feature

Available Values

: ON/OFF

Default

: OFF

ODE

ELECTION

ETAILS

Summary of Contents for VX-8DE





















































































































































































Search results

Summary of Contents for VX-8DE

Reviews:

Related manuals for VX-8DE

Brands by name

Popular brands

Yaesu VX-8DE, Operating Manual

Search results

Summary of Contents for VX-8DE

Reviews:

Related manuals for VX-8DE

Brands by name

Popular brands