Yaesu FTM-350AE, Technical Supplement

Page: 9 / 67

13
FTM-350AR/E Technical Supplement
18.To change the mode to "WIDE FM", just repeat
steps 3 through 7 above, rotating the left DIAL
knob to select "WIDE FM" in step 6 above.
19.Set the RF signal generator to 440.050 MHz. Set
the generator for ±22.5 kHz deviation of a 1 kHz
modulation tone, and set the RF output level from
the signal generator to -1 dB
μ V.
20.Set the transceiver frequency to 440.050 MHz.
21.Press the [
ADJ
] key to set the alignment Menu
Item “
SQLA U D SQLA U D SQLA U D SQLA U D SQLA U D
”.
22.Press the [ BCK
] key to save the new setting.
23.Increase the output level of the signal generator
up to +7 dB μ V.
24.Press the [ FWD
] key to save the new setting.
25.Set the transceiver and RF signal generator fre-
quency to 146.050 MHz.
26.Increase the output level of the signal generator
up to -1 dB μ V.
27.Press the [ ADJ
] key to set the alignment Menu
Item “
SQLA U D SQLA U D SQLA U D SQLA U D SQLA U D
”.
28.Press the [ BCK
] key to save the new setting.
29.Increase the output level of the signal generator
up to +7 dB μ V.
30.Press the [
FWD
] key to save the new setting.
31.Press and hold in the [ ADJ
] key for one second,
to set the alignment Menu Item “
SQLB U D SQLB U D SQLB U D SQLB U D SQLB U D
”.
32.Just repeat all steps above, in "SUB BAND".
S-Meter Calibration
1. Set the RF signal generator to 440.050 MHz. Set
the generator for ±3.5 kHz (±22.5 kHz for Wide
FM) deviation of a 1 kHz modulation tone, and
set the RF output level from the signal generator
to -5 dB
μ V.
2. Set the transceiver frequency to 440.050 MHz.
3. Press the [
SET
] key to enter the SET mode.
4. Rotate the left DIAL knob to select Menu Item "TX/
RX".
5. Press the left DIAL knob, then rotate the left DIAL
knob to select "B08 WIDE/NARROW AUTO".
6. Press the left DIAL knob, then rotate the left DIAL
knob to select "AUTO (FM)".
7. Press the [ ESC
] key repeatedly, to save the new
setting and exit the Menu mode.
8. Press the [ ADJ
] key to set the alignment Menu
Item “
SMA U D SMA U D SMA U D SMA U D SMA U D
”.
9. Press the [ BCK
] key to save the new setting.
10.Increase the output level of the signal generator
up to +23 dB μ V.
11.Press the [ FWD
] key to save the new setting.
12.To change the mode to "WIDE FM", just repeat
steps 3 through 7 above, rotating the left DIAL
knob to select "WIDE FM" in step 6 above.
13.Increase the output level of the signal generator
up to 0 dB μ V.
14.Press the [ BCK
] key to save the new setting.
15.Increase the output level of the signal generator
up to +23 dB μ V.
16.Press the [ FWD
] key to save the new setting.
17.To change the mode to "FM", just repeat steps 3
through 7 above, rotating the left DIAL knob to
select "FM" in step 6 above.
18.Set the transceiver and RF signal generator fre-
quency to 146.050 MHz.
19.Increase the output level of the signal generator
up to -5 dB μ V.
20.Press the [ BCK
] key to save the new setting.
21.Increase the output level of the signal generator
up to +23 dB μ V.
22.Press the [
FWD
] key to save the new setting.
23.To change the mode to "WIDE FM", just repeat
steps 3 through 7 above, rotating the left
DIAL
knob to select "WIDE FM" in step 6 above.
24.Increase the output level of the signal generator
up to 0 dB μ V.
25.Press the [
BCK
] key to save the new setting.
Alignment