Yaesu FTM-10R, Technical Supplement

Page: 12 / 64

12
FTM-10R/E Technical Supplement
UHF Transmitter Output
1. Press the key repeatedly to display the fre-
quency.
2. Set the transceiver frequency to 440.050 MHz.
3. Press and hold the
key for one second to
enter the Menu mode.
4. Rotate the DIAL knob to select Menu Item "
F44 TX F44 TX F44 TX F44 TX F44 TX
POWER POWER POWER POWER POWER
".
5. Press the
    
key, then rotate the DIAL knob to select
"
LOW
".
6. Press the key to save the new setting and
exit the Menu mode.
7. Press the key repeatedly to display the
Alignment Menu.
8. Press the
    
key repeatedly to select Alignment Menu
Item "
A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx
".
9. Key the transmitter and rotate the DIAL knob to adjust
transmit power to 5 ± 0.3 Watts on the wattmeter.
10.Press the key to save the new setting and
exit the Alignment Menu mode.
11.To change the TX Power to "MID", just repeat steps 3
through 6 above, rotating the DIAL knob to select "
MID
"
in step 5 above.
12.Press the key repeatedly to display the
Alignment Menu mode.
13.Press the
    
key repeatedly to select Alignment Menu
Item "
A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx
".
14.Key the transmitter and rotate the DIAL knob to adjust
transmit power to 20 ± 0.5 Watts on the wattmeter.
15.Press the key to save the new setting and
exit the Alignment Menu mode.
16.To change the TX Power to "HIGH", just repeat steps 3
through 6 above, rotating the DIAL knob to select "
HIGH
"
in step 5 above.
17.Press the key repeatedly to display the
Alignment Menu mode.
18.Press the
    
key repeatedly to select Alignment Menu
Item "
A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx A-2 PWR. xxx
".
19.Key the transmitter and rotate the DIAL knob to adjust
transmit power to 40 ± 0.5 Watts on the wattmeter.
20.Press the key to save the new setting and
exit the Alignment Menu mode.
VHF Transmitter Deviation
1. Inject a 1 kHz audio tone at a level of 25 mV from the
AF generator into the microphone jack (pin 1).
2. Press the key repeatedly to display the fre-
quency.
3. Set the transceiver frequency to 146.050 MHz.
4. Press and hold the
key for one second to
enter the Menu mode.
5. Rotate the DIAL knob to select Menu Item "
F44 TX F44 TX F44 TX F44 TX F44 TX
POWER POWER POWER POWER POWER
".
6. Press the
    
key, then rotate the DIAL knob to select
"
LOW
".
7. Press the key to save the new setting and
exit the Menu mode.
8. Press the key repeatedly to display the
Alignment Menu.
9. Press the
    
key repeatedly to select Alignment Menu
Item "
A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx
".
10.Key the transmitter, and rotate the DIAL knob to ad-
just transmit deviation to 4.5 kHz ± 0.2 kHz on the de-
viation meter.
11.Press the key to save the new setting and
exit the Alignment Menu mode.
UHF Transmitter Deviation
1. Inject a 1 kHz audio tone at a level of 25 mV from the
AF generator into the microphone jack (pin 1).
2. Press the key repeatedly to display the fre-
quency.
3. Set the transceiver frequency to 440.050 MHz.
4. Press and hold the
key for one second to
enter the Menu mode.
5. Rotate the DIAL knob to select Menu Item "
F44 TX F44 TX F44 TX F44 TX F44 TX
POWER POWER POWER POWER POWER
".
6. Press the
    
key, then rotate the DIAL knob to select
"
LOW
".
7. Press the key to save the new setting and
exit the Menu mode.
8. Press the key repeatedly to display the
Alignment Menu.
9. Press the
    
key repeatedly to select Alignment Menu
Item "
A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx A-3 DEV. xxx
".
10.Key the transmitter, and rotate the DIAL knob to ad-
just transmit deviation to 4.5 kHz ± 0.2 kHz on the de-
viation meter.
11.Press the key to save the new setting and
exit the Alignment Menu mode.
Alignment