Yaesu FT-818ND Operating Manual Download Page 16

Page: 16 / 76

MIC

SP/PH SP PH

① ② ③

MIC

Jack

Connect the supplied

MH-31

A8J

Hand Microphone to this jack.

MIC

FAST

GND

PTT

MIC MIC GND

+5 V

DOWN

SP/PH

Jack

This 3.5-mm, 2-pin jack provides variable audio output for an external speaker (4

Ω

impedance) or earphones. The audio level varies according to the setting of the

front panel’s

knob.

When you insert an earphone plug into this jack, the

SP-PH

slide switch (located

to the right side of this jack)

MUST BE

set to the “

” position, to prevent the

possibility of injury to your ears.

SIGNAL

GND

SP-PH

Switch

If you use earphones with this transceiver, move this switch to the “

” position before

inserting the earphone plug into the

SP/PH

Jack, to prevent injury your ears.

Side Panel Switch & Connectors

Summary of Contents for FT-818ND













































































Search results

Summary of Contents for FT-818ND

Reviews:

Related manuals for FT-818ND

Brands by name

Popular brands

Yaesu FT-818ND, Operating Manual

Search results

Summary of Contents for FT-818ND

Reviews:

Related manuals for FT-818ND

Brands by name

Popular brands