27
Set the tone signal type for analog FM mode
1
Touch [
SETUP
], then touch [
F
], and then touch [
SQL
].
2
Select [
RX SQL
] to set the tone signal type during reception, or select
[
TX SQL
] to set the tone signal type during transmission.
3
Touch [
▲
] or [
▼
].
The setting will change in the following sequence each time [
▲
] or [
▼
]
is touched.
à
“OFF”
à
“TONE”
à
“DCS”
à
S E T U P
U P
N K
I
L
N K
I
L
8
7
D O W N
F
M
/
V
S Q L
Tx PW R
H I
BACK
BACK
ID SET
TIMER ID ANNOUNCE
MODE/REMOTE
D G - I D
ID MODE
���������
SQL
R - O F F
T - O F F
DEVIATION
WIDE
4
Touch [
BACK
] 3 times.
The setting is determined and the display will return to the operation mode screen.
z
Factory default: OFF
z
Both TX and RX can be set to different tone signal type.
Setting the display turn-off time
1
Touch [
SETUP
], then touch [
F
], and then touch [
MODE/REMOTE
].
2
Touch [
DISPLAY TIMER
] to display “ON” or “OFF”.
The set value will change between “OFF” and “ON” each time
[
DISPLAY TIMER
] is touched.
3
Touch [
SETUP
].
The display timer setting screen will be displayed.
4
Touch [
TIMER
].
The set value will change in the following sequence each time [
TIMER
],
[
▲
], or [
▼
] is touched (Default 1min).
à
“1min”
à
“5min”
à
“10min”
à
“30min”
à
S E T U P V e r . 1 . x x x E X P A 1
U P
N K
I
L
N K
I
L
D O W N
F
M
/
V
S Q L
Tx PW R
H I
BACK
BACK
ID SET
TIMER ID ANNOUNCE
MODE/REMOTE
D G - I D
ID MODE
���������
SQL
R - O F F
T - O F F
DEVIATION
WIDE
5
Touch [
BACK
] 4 times.
The setting is determined and the display will return to the operation mode screen.
z
Factory default:
DISPLAY TIMER: ON
TIMER: 1min
Password
To continue operating the DR-1X when the power is turned ON or after the display has been turned OFF, the
password must be entered.
z
Password is factory set to “
0000
”. It is possible to change the password.
z
If you forget your password, you will need to do an all reset. Please note that when all reset is performed, all settings
and memory contents are returned to the factory default state.
z
Use the factory default password “0000”, unless it is necessary to change it for management security.
1
Touch [
SETUP
], then touch [
F
], and then touch [
MODE/REMOTE
].
S E T U P V e r . 1 . x x x E X P A 1
U P
N K
I
L
N K
I
L
D O W N
F
M
/
V
S Q L
Tx PW R
H I
BACK
BACK
ID SET
TIMER ID ANNOUNCE
MODE/REMOTE
D G - I D
ID MODE
���������
SQL
R - O F F
T - O F F
DEVIATION
WIDE
2
Touch [
DISPLAY TIMER
].
3
If [
DISPLAY TIMER
] is set to “OFF”, touch [
DISPLAY TIMER
] and turn
it to “ON”.
4
Touch [
SETUP
].
REMOTE / COMMAND / DISP TIMER
M
/
V
BACK
BACK
>
>
COMMAND
>
REMOTE
OFF
DG-ID
DISPLAY TIMER
ON