Xylem FLYGT SmartRun SRC 311 User Manual Download Page 18 | Manualshive

Page: 18 / 24

background image

Do not connect directly into an Ethernet port. The voltage destroys the Ethernet device.

NOTICE:

This RJ45 connector is not an Ethernet connection. Do not connect directly to an Ethernet
port.

1

8

7

6

5

4

3

2

WS003606

1. Not used
2. Not used
3. 0 V
4. Optibus -
5. O
6. +24 V, power supply for the remote key pad
7. RS485- Modbus RTU/CanOpen
8. RS485+ Modbus RTU/CanOpen

All SRC 311 parameters are read and set over the fieldbus communication. Process
parameters marked as setting is also accessed and read, but process parameters marked
as fixed value cannot be read or set over the fieldbus communication.
Any external system that wants to read process data and alarms from SRC 311 must be
configured with the correct parameter addresses for SmartRun

™

.

System Description

16

SRC 311 - SmartRun

™

User guide

«
...
16
17
18
19
20
...
»

Summary of Contents for FLYGT SmartRun SRC 311

























Reviews:

No comments

Related manuals for FLYGT SmartRun SRC 311

Brand: H3C Pages: 5

Brand: H3C Pages: 27

Brand: H3C Pages: 4

Brand: H3C Pages: 54

Brand: H3C Pages: 10

Brand: H3C Pages: 10

Brand: Panasonic Pages: 8

Brand: Daruifuno Pages: 24

Brand: Digiplex Pages: 48

Brand: Moog Pages: 15

Ames Colt Series

Brand: Watts Pages: 8

Brand: CAME Pages: 40

Brand: Bucher Hydraulics Pages: 86

Brand: SAFERA Pages: 32

TotalArc BMS 460346 SOLAR POWER

Brand: OGI Pages: 28

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Brand: KWC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands