manualshive.com logo in svg

Xylem Flygt 2250, Installation, Operation And Maintenance Manual

Share
Download
Xylem Flygt 2250 Installation, Operation And Maintenance Manual Download Page 19

WARNING:

Do not install the starter equipment in an explosive zone unless it is explosion-proof rated.

Three thermal contacts are incorporated in the stator. They are normally closed.
Thermal contacts must never be exposed to voltages higher than 250 V, breaking current
maximum 6 A at a power factor 0.6. It is recommended that the thermal contacts are
connected to 24 V over a separate fuse to protect any other automatic equipment.

Cable charts

Connection locations

WS001021B

L1 L2 L3

T3 T4

T1 T2

15

13

14

4

2

3

1

7

10

5

9

8

6

11

12

17

16

24

22

23

19

20

21

18

1

Starter equipment and main leads (L1, L2, L3)

13

Coil

2

Earth (ground)

14

Transformer

3

Functional ground

15

Capacitor

4

Control leads (T1, T2, T3, T4)

16

Softstarter

5

Phase shifter

17

Level regulator

6

Diode

18

Contactor, start relay or thermal relay

7

Motor cable, minimum 20 m (66 ft.)

19

Thermal detector in stator

8

Screen

20

Thermal detector in main bearing

9

Pump

21

Jumper

10

Crimp connection

22

Terminal board, terminal plate

11

Crimp isolation

23

Leakage sensor

12

Motor protector

24

Stator leads (U1, U2, U5, U6, V1, V2, V5, V6,

W1, W2, W5, W6, Z1, Z5, Z6)

Installation

Flygt 2250 Installation, Operation, and Maintenance Manual

17

Summary of Contents for Flygt 2250











































Reviews:

No comments

Brands by name

Popular brands

Load more brands