manualshive.com logo in svg

Xylem Flygt 2250, Installation, Operation And Maintenance Manual

Share
Download
Xylem Flygt 2250 Installation, Operation And Maintenance Manual Download Page 11

Product Description

Products included

Pump model

Approvals

2250.011

Standard

Pump design

The pump is submersible, and driven by an electric motor.

Intended use

The product is intended for moving waste water, sludge, raw and clean water. Always
follow the limits given in 

Application limits

 (page 36). If there is a question regarding the

intended use of the equipment, please contact an Xylem representative before
proceeding.

WARNING:

In explosive or flammable environments, only use Ex- or MSHA-approved pumps.

NOTICE:

Do NOT use the pump in highly corrosive liquids.

For information about pH, see 

Application limits

 (page 36).

Particle size

The pump can handle liquid containing particles that correspond to the holes in the
strainer.

Number of holes

Hole dimensions

508

15×45 mm (0.6×1.77 in.)

Pressure class

MT

Medium head

HT

High head

Impeller type

B

Wear resistant

Poly-Life

®

The pump is available with Poly-Life

®

 polyurethane wear parts for extra resistance.

Monitoring equipment

The following applies to the monitoring equipment of the pump:

• The stator incorporates thermal contacts connected in series that activate the alarm at

overtemperature.

• The thermal contacts open at 125°C (257°F) and close at 95°C (203°F)

Product Description

Flygt 2250 Installation, Operation, and Maintenance Manual

9

Summary of Contents for Flygt 2250











































Reviews:

No comments

Brands by name

Popular brands

Load more brands