Xylem Bell & Gossett CRS Instruction Manual Download Page 9

4  Installation

4.1  Precautions

Before starting work, make sure that the safety instructions in the chapter 

Introduction and

Safety

 on page 2 have been read and understood.

WARNING: STRONG MAGNETIC FIELD
This product may contain strong magnets which can be harmful to pacemaker wearers and

others with medical implants. Those with implanted medical devices must stay back 36 in

(90 cm). Keep tools and other loose metal objects away. The magnets in this product are

strong enough to pull them from your hand or can cause a loss of balance. To avoid

damage, keep magnetic media such as computer discs, credit cards, and tapes away.

Failure to follow these instructions could result in serious personal injury, death, and/or

property damage. 

WARNING:
Do not operate the unit in an area where explosive gases are present.

WARNING:
The heating of water and other fluids causes volumetric expansion. The associated forces

can cause the failure of system components and the release of high-temperature fluids. In

order to prevent this, install properly sized and located compression tanks and pressure-

relief valves. Failure to follow these instructions can result in serious personal injury or

death, or property damage.

WARNING:
This product can expose you to chemicals including Lead, which is known to the State of

California to cause cancer and birth defects or other reproductive harm. For more

information go to: www.P65Warnings.ca.gov.

CAUTION:
Installation and maintenance must be performed by a qualified professional. Service should

not be performed on any component in an active hydronic system. Before attempting to

make any required adjustments, properly shut-off the water supply and water heater, drain

the lines, and allow the system to reach a safe handling temperature (below 100°F [38°C])

and zero pressure condition. Use proper safety equipment including gloves, goggles, or

similar tools to avoid contact with system fluids and common hazards. Failure to follow these

instructions could result in personal injury and property damage.

CAUTION:
Read this manual carefully before installing and using the product. Improper use of the

product can cause personal injury and damage to property, and may void the warranty.

CAUTION:
The operator must be aware of safety precautions to prevent physical injury.

4  Installation

CRS Instruction Manual

7

Summary of Contents for Bell & Gossett CRS





















Reviews: