background image

Important Safety Instructions 

1) Read these instructions. 

2) Keep these instructions. 
3) Heed all warnings. 
4) Follow all instructions. 

5) Do not use this equipment near water. 
6) Clean only with dry cloth. 
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other equipment 
(including amplifiers) that produce heat. 
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades 

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide 
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, 
consult an electrician for replacement of the obsolete outlet. 

10) Protect power cords from being walked on or pinched particularly at plugs, convenience receptacles, and 
the point where they exit from the equipment. 
11) Only use attachments/accessories specified by the manufacturer. 

12) For products that are not rack-mountable: Use only with a cart, stand, tripod, bracket, or table specified 
by the manufacturer, or sold with the equipment. 
When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tip-over. 

13) Unplug this equipment during lightning storms or when unused for long periods of time. 
14) Refer all servicing to qualified service personnel. Servicing is required when the equipment has been 
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have 

fallen into the equipment, the equipment has been exposed to rain or moisture, does not operate normally, 
or has been dropped. 
15) For products that are a Mains powered device: 

The equipment shall not be exposed to dripping or splashing and no objects filled with liquids (such as 
vases) shall be placed on the equipment. 
Warning! To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. 

16) For products containing a lithium battery: 
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent 
type. 

17) The main power switch is located on the back of XXL MCL mixers. It should remain accessible after 
installation. 

18) The equipment shall be used at a maximum ambient temperature of 40° C. 
19) Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably 
in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to 

sufficiently intense noise for a period of time. To ensure against potentially dangerous exposure to high 
sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high 
sound pressure levels use hearing protectors while the equipment is in operation. Ear plugs or protectors in 

the ear canals or over the ears must be worn when operating the equipment in order to prevent permanent 
hearing loss. 
 

Environmental Compliance 

Disposal of Waste Equipment by Users in the European Union 
This symbol on the product or its packaging indicates that this product must not be disposed of with other 

waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated 
collection point for the recycling of waste electrical and electronic equipment. The separate collection and 
recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure 

that it is recycled in a manner that protects human health and the environment. For more information about 
where you can drop off your waste equipment for recycling, please contact your local city recycling office or 
the dealer from whom you purchased the product.  

 

CE/EMC 

Carisch SpA declares that this product complies with the following standards regulating emissions and 
immunity:  
- 89/336/EEC (EMC) and subsequent amendments 92/31/EEC e 93/68/EEC (EN 55103-1 e EN 55103-2) 

- 73/23/EEC (LVD) and subsequent amendments 93/68/EEC (EN 60065)

Summary of Contents for MCL16Pro

















Reviews: