Voltage:
18V
No Load Speed:
12,500/min
Max. Air Speed:
210km/hour
Battery:
1.5Ah Li-Ion
Charge Time:
4-5 Hours
Charger Input:
100-240VAC, 50-60Hz, 14.5W
Charger Output:
21V DC, 400mA
Tool Weight:
1.62kg
SPECIFICATIONS
OPERATION
4
Inserting & Removing the Battery
1. To insert, align the ribs of the battery with the battery
recess and slide the battery in so that it clicks into
place.
FIG. F.
2. To remove, first press and hold the battery release tab
(a), then side the battery out (b).
FIG. G.
Switching On and Off
To turn the blower ON, press the on/off switch to the
“ I ”(ON position).
FIG. H.
To turn the blower OFF, press the on/off switch to the
“O”(OFF position).
FIG. I.
Blowing
The blower is ideal for blowing leaves, grass clippings
and other debris.
Hold the blower firmly, turn the switch on, point the jet
of air in front of you and move forward slowly. Move the
blower from side to side, with the tube several inches
above the ground.
FIG. J.
Be careful where you point the jet of air as it can
move heavy material and cause injury or damage to
bystanders.
Note:
Be aware of other people and animals in the
area where you are to be operating the blower.
Note:
Avoid collisions with hard objects which could
damage your blower.
PROPER USE
This tool is intended for use in a DIY (Do It Yourself)
context or for hobbyist purposes. It is not built for
continuous daily use in a trade or professional capacity.
Before using the machine, carefully read these
instructions, especially the safety rules to help ensure
that your machine always operates properly.
Before attempting to operate the machine, familiarise
yourself with the controls and make sure you know how
to stop the machine quickly in an emergency.
Save these instructions and the other documents
supplied with this machine for future reference.
ASSEMBLY
Charging the Li-Ion Battery
WARNING!
Ensure the tool is turned off
and battery disconnected before performing
any of the following operations. Wear gloves,
blades are sharp.
NOTE:
The battery will not develop a memory, it does
not have to be fully discharged before recharging.
1. Connect the charging adaptor into the mains power
outlet.
2. The charger LED will flash green showing power is
being supplied to the charger.
3. With the battery sitting on a flat surface, align the
raised ribs on the battery with the recess in the
charger cradle and slide onto the battery ensuring a
firm connection.
FIG. C.
4. The charger LED will illuminate red signifying that the
battery is charging. Battery is fully charged after 4-5
hours, green LED will illuminate.
5. When removing the charger from the battery, first
press the battery release tab, then slide the cradle from
its position.
FIG. D.
WARNING!
Do not use any attachments
or accessories not recommended by the
manufacturer of this product, as it can result in
serious personal injury.
WARNING!
To reduce the risk of electrical
shock, we recommend the use of a residual
current device rated 30mA or less.
Charger LED Indicators
LED Indicator
Situation
GREEN (Flashing)
Stand By (no battery
pack is inserted)
RED (Illuminated)
Battery is charging
(low charge)
GREEN (Illuminated)
Battery is fully
charged.
GREEN & RED (Flashing) Battery is faulty
GREEN & RED
(Illuminated)
Battery is too hot.
Remove battery
from charger a let
cool. Insert battery
again when at room
temperature
BATTERY
Fitting the Blower Tube
1. Remove assembly screw from underside of motor
housing and put aside. Align the tube with the outlet
of the blower.
FIG. A.
2. Push the blower tube onto the blower until the tube
release clicks into place. Refit assembly screw
removed in step 1.
FIG.B.
Battery Charge Indicator
The included battery is equipped with a battery charge
indicator to show the state of the battery charge.
Press the charge indicator button and check to see
which LED light is illuminated.
FIG. E
1 GREEN LED
indicates that the battery has only a
low charge and requires charging.
2 GREEN LEDs
indicate that the battery has mid
state of charge.
3 GREEN LEDs
indicate that the battery is fully
charged.
Battery Protection System
The tool is equipped with the battery protection system,
which helps to ensure a long service life.
The output power automatically cuts off during operation
when the tool and battery are placed under the following
situations:
• When tool is overloaded:
If this occurs, turn off the tool and let it cool down for
10 mins, remove the cause of overload, then resume
operation.
• When the remaining battery capacity
becomes low:
Recharge the battery pack.
WARNING!
Never use the blower unless
the blower tube is properly fitted.
Allow at least 3 hours of charge time before initial use
of the battery. Charge the battery pack only with the
charger provided. The battery should be charged in a
cool dry place. It will take 2 to 3 charging/discharging
cycles before the battery achieves maximum run time
capacity.
WARNING!
Dress properly. Do not wear
loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
