manualshive.com logo in svg

Xtreme P90L-1500, User & Installation Manual

Share
Download
Xtreme P90L-1500 User & Installation Manual Download Page 19

Xtreme Power Conversion Corporation

P90L 1500–3000 User’s Manual

Page 19

Uninterruptible Power Supply

Display

Function

Backup time information

Indicates the backup time in pie chart.

Indicates the backup time in numbers.

H: hours, M: minutes

Warning & Fault information

Indicates that the warning and fault occurs.

Indicates the warning fault codes, and the codes are listed in details in this 

manual.

Setting Operation

 

Indicates the setting operation.

Input / Output & Battery information

 

Indicates the output/input voltage, output/input frequency or battery volt

-

age. V: output voltage, Hz: frequency

Load information

 

Indicates the load level by 0-25%, 26-50%, 51-75%, and 76-100%.

 

Indicates overload.

Indicates the load or the UPS output is short circuited.

UPS Status

Indicates that programmable management outlets are working.

 

Indicates the UPS is working in online mode.

 

Indicates the UPS is working in converter mode.

 

Indicates the UPS is working in bypass mode.

 

Indicates the UPS is powering the output directly from utility.

 

Indicates that the UPS alarm is disabled.

Indicates the battery charger is working.

Summary of Contents for P90L-1500



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands