manualshive.com logo in svg

Xtreme 61038, Owner'S Manual And Safety Instructions

Share
Download
Xtreme 61038 Owner'S Manual And Safety Instructions Download Page 18

WOOD CHIPPER

18

GB

Problem

Cause

Remedy

Engine fails to start

1.   Spark plug wire is 
disconnected
2.  Out of fuel or stale fuel
3.   Engine and/or Fuel valve is 

not in ON position

4.  Choke lever is not in CLOSE 
position
5.  Blocked fuel line
6.  Fouled spark plug
7.  Engine flooding
8.  No oil in engine

1.    Attach spark plug wire securely to 

spark plug

2.  Fill with clean, fresh gasoline
3.   Engine and Fuel valve must be in 

ON position

4.   Choke level must be in CLOSE 

position for a cold start

5.   Clean fuel line
6.   Clean, adjust gap, or replace
7.   Wait a few minutes to restart, but 

do not prime

8.   Add engine oil to engine

Engine runs 
erratically

1.   Spark plug wire is loose
2.   Unit running with Choke lever 

in CLOSE position

3.  Blocked fuel line or stale fuel
4.  Vent plugged
5.  Water or dirt in fuel system
6.  Dirty air cleaner
7.   Improper carburetor 

adjustment

1.    Connect and tighten spark plug 

wire

2.   Move choke lever to OPEN position
3.   Clean fuel line. Fill tank with clean, 

fresh gasoline

4.   Clear vent
5.   Drain fuel tank. Refill with fresh fuel
6.   Clean or replace air cleaner
7.   Refer to engine manual

Engine overheats

1.   Engine oil level low
2.  Dirty air cleaner
3.  Air flow restricted
4.   Carburetor not adjusted 

properly

1.   Fill crankcase with proper oil
2.   Clean air cleaner
3.   Remove housing and clean
4.   Refer to engine manual

Chipping action 
seems too slow, 
cutting disk stalls, 
or no material is 
discharged when 
engine is running

1.    Engine speed is too slow 

causing belt to slip

2.  Knives are dull or damaged
3.   Cutting disk is jammed by 

debris from the feed hopper 
and discharge chute

4.  Discharge chute is clogged

1.   Run the engine at full throttle
2.   Sharpen or replace knives
3.   Remove any built-up debris and 

turn cutting disk with a wooden 
stick to be sure it turns freely

4.   Clean out debris

When chipping, 
branch seems to 
vibrate and move 
about excessively 
with unusual noise

1.   Knives are dull or damaged
2.   Knives are not properly seated 

on the cutting disk

3.   Rotor is overloaded with 

material

1.   Sharpen or replace knives
2.   Loosen the knife mounting screws, 

reset the knives and tighten the 
screws

3.   Allow unit to clear itself before 

adding more material to the hopper

TROUBLE SHOOTING

36060UK00M100_BS.indd   18

2019/8/28   14:44:33

WOOD CHIPPER

19

GB

OPTIONAL

PARTS SCHEDULE

36060UK00M100_BS.indd   19

2019/8/28   14:44:34

Summary of Contents for 61038






















Reviews:

No comments

Brands by name

Popular brands

Load more brands