Xtreme 20kVA User And Installation Manual Download | Manualshive

Page: 20 / 62

background image

R90 ONLINE USER’S MANUAL

UNINTERRUPTIBLE POWER SUPPLY (UPS)

Xtreme Power Conversion Corporation (Rev 3/7/14)

Page 20

UPS Multi-Module Installation

The basic installation procedure for a parallel system consisting of two or more R90-20KVA modules is
that same as that of a single module. The following provides installation procedures related to a parallel
system.

Cabinet Installation

Connect all R90-20KVA UPS required in the parallel system as shown in the diagram below.

Note:

If installing 5-6 units in parallel, remove the jumper cap J30 on the control inspection board

(MHTBJHR1CU04 in all UPS to be connected in parallel.

If installing 7-10 units in parallel, remove the jumper cap J30/J31 on the control inspection

board (MHTBJHR1CU04 in all UPS to be connected in parallel.

Make sure that each UPS input breaker is in the “OFF” position and there is no output from any UPS
connected. The battery strings can be connected separately or in parallel.

WARNING!

MAKE SURE THE N, A(L1), B(L2), AND C(L3) WIRING IS CORRECT, AND THAT GROUND

IS CONNECTED.

«
...
18
19
20
21
22
...
»

Summary of Contents for 20kVA































































Reviews:

No comments

Related manuals for 20kVA

Brand: GE Pages: 24

Brand: CyberPower Pages: 2

Brand: Apricorn Pages: 16

Brand: Eaton Pages: 2

Brand: LESTAR Pages: 2

Brand: LESTAR Pages: 2

Brand: LESTAR Pages: 2

DX-EMC34 Series

Brand: Eaton Pages: 7

Brand: Eaton Pages: 32

Pulsar EX RT 5000

Brand: Eaton Pages: 44

ModularEasy 9PXMEZ11Ki

Brand: Eaton Pages: 124

Evolution 1250 RT 2U

Brand: Eaton Pages: 158

Brand: Tripp Lite Pages: 36

SmartOnline SU2200RMNAFTA

Brand: Tripp Lite Pages: 7

SmartOnline SU1000XLA

Brand: Tripp Lite Pages: 6

SmartOnline SU10KRT3U

Brand: Tripp Lite Pages: 7

Brand: Sollatek Pages: 2

Voltsure Ultima LCD 650

Brand: Sollatek Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands