manualshive.com logo in svg

Xtool D1 Pro, Quick Start Manual

The Xtool D1 Pro is an advanced diagnostic device designed for professionals. With its user-friendly interface, it allows you to easily troubleshoot and diagnose vehicle issues. Unlock the full potential of your Xtool D1 Pro by downloading the free manual from manualshive.com. Get the most out of your tool with this comprehensive manual, readily available for download.

Share
Download
background image

Tips

 × 2 

1 : 1

The screws are used to set the tension of the timing belts. Do not 

fully tighten them. Otherwise, the timing belts may be damaged.

If you can't put the shaft through the 

timing belt, the possible cause is that 

the timing belt is set too tight. You can 

adjust its tension by turning the screw.

8

7

Summary of Contents for D1 Pro




























Reviews:

No comments

Related manuals for D1 Pro

Pro's Kit PT-5203A Quick Manual preview
PT-5203A
Brand: Pro's Kit Pages: 2
Panasonic LP-400 Series Operation And Maintenance Manual preview
LP-400 Series
Brand: Panasonic Pages: 334
MARKING METHODS MARK 300 SERIES Manual preview
MARK 300 SERIES
Brand: MARKING METHODS Pages: 8

Brands by name

Popular brands

Load more brands