background image

PERSONAL SAFETY

a)Stay alert and do not use the tool when under influence of alcohol.

b)Use safety glasses and face or dust mask. Wear protective hearing equipment, helmet and

boots.

c)Avoid unintentional starting. Before connecting to power source or battery, make sure the

switch is at OFF position.

d)Dress properly. Do not wear loose clothing or jewelry. They can be caught with moving parts.

e) Remove adjusting keys and wrenches. Tool or adjusting key you leave attached to a turning

part of the tool may cause injury.

f)

Do not overreach. Proper footing and balance at all times allow better control of the tool in unexpected

situations.

g)

Use approved protective equipment only.

ELECTRIC SAFETY

a)

The power cord plug shall always suit the socket. Never adjust the socket. Do not use

plug hubs. Non-adjusted plugs and appropriate sockets reduce the risk of electric shock injury.

b)

Prevent body contact with conductive surfaces to avoid a risk of electric shock injury.

c)

Do not expose the tool to rain or wet locations. Presence of water in electric tool highly increases the risk

of electric shock injury.

d)

Do not force the cord. Keep the cord away from heat sources, oil, sharp edges or movable parts. Damaged

cord increases a risk of electric shock injury.

e)

When manipulating in exterior areas consider an extension cord intended for outdoor use specifically.

Using an exterior extension cord decreases a risk of electric shock injury.

f)

It is strictly recommended to use a ground fault circuit interrupter (GFCI) when manipulating the tool in a

wet area. Using of GFCI decreases a risk of electric shock injury.

g)

A double insulated tool is equipped with a polarized plug (one prong is wider than the other). If the

connector does not fully suit the socket, turn the plug. Do not change the plug by any means. Double insulation

eliminates the need for grounding of power cord and power supply system.

1.

Latch

2.

rotation direction

3.

spindle

4.

cover

5.

inner flange

6.

disc

7.

outer flange

8.

Key

9.

handle

10.

switch latch

11.

switch

Summary of Contents for XT105125



















Reviews: