background image

                                                                                                                                         

Xterra  FS220e  Elliptical

13

Console Operation

Quick Start mode

This is the quickest way to start a workout. After the console powers up you just press the Start key
to begin. In Quick Start the Time will count up from zero and the workload may be adjusted
manually by pressing the Up or Down keys. Press the Enter key to switch between the Speed in
MPH or RPM readings.

Basic information and functions:

The

Data  displays:

Calories

show an accumulation of calories burned (Kcal). The number shown is just an

estimate; your actual calorie burn most likely will be different. The only way to get an
accurate calorie reading is in a laboratory setting connected to a host of machines.

Time

 shows elapsed time unless you set the timer to count down.

Pulse

 indicates your heart rate if you are grasping the hand pulse sensors.

RPM

 displays your pedaling speed in revolutions per minute.

Speed

 shows your speed in miles per hour (or KM if units are set to metric, see

maintenance section page 18).

Distance

 displays accumulated mileage. The Distance window will also display an M or KM

indicating if the readout is in Kilometers (KM) or Miles (M).

The Elliptical has a built in

heart rate monitoring system

. Simply grasping the hand pulse sensors

on the stationary handle bars will start the heart Icon blinking (this may take a few seconds). The
Pulse Display Window will display your heart rate, or Pulse, in beats per minute.

The

Stop/Reset

 button actually has several functions. Pressing the Stop/Reset key once during a

program will

Pause

 the program for 5 minutes. If you need to get a drink, answer the phone or any

of the many things that could interrupt your workout, this is a great feature. To resume your workout
during Pause just press the Start key. If the Stop/Reset button is pressed twice during a workout the
program will end

.

There is an

Audio Input Jack

 on the front of the console and built-in speakers. You may plug any

low-level audio source signal into this port. Audio sources include MP3, Ipod, portable radio, CD
player or even a TV or computer audio signal.

Programming the console

Each of the programs can be customized with your personal information and changed to suit your
needs. Some of the information asked for during programming is necessary to ensure the readouts
are correct. You will be asked for your

Age

and

Weight

. Entering your

Age

 is necessary during the

Heart Rate control program to ensure the correct settings are entered in the program. Entering your

Weight

 aides in calculating a more correct

Calorie

 reading; although we cannot provide an exact

calorie count we do want to be as close as possible.

A message about Calories

: Calorie readings on every piece of exercise equipment, whether it is

in a gym or at home, are not accurate and tend to vary widely. They are meant only as a guide to
monitor your progress from workout to workout. The only way to measure your calorie burn
accurately is in a clinical setting connected to a host of machines.

Summary of Contents for FS220e





















Reviews: