background image

2

ERG500 Rower

•  Do not operate equipment on deeply padded, plush or shag carpet. Damage to both carpet and  

equipment may result.

•  Before beginning this or any exercise program, consult a physician. This is especially important for  

persons over the age of 35 or persons with pre-existing health conditions.

•  Keep hands away from all moving parts.

•  Do not attempt to use your equipment for any purpose other than for the purpose it is intended.

•  Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your  

equipment. Quality athletic shoes are recommended to avoid leg fatigue.

•  Wear proper clothing for exercising, loose clothing could become caught in the machine.

•  Only one person at a time should use the machine.

•  If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout 

at once. CONSULT A PHYSICIAN IMMEDIATELY.

•  Do not place any sharp object around the machine. 

 

Important Safety Instructions

When using an appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.

WARNING

 - To reduce the risk of burns, fire electric shock, or injury to persons: 

1.  Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury 

to persons.

2.  Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled 

persons.

3.  Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same 

room with the machine.

4.  Use this appliance only for its intended use as described in this manual. Do not use attachments not  

recommended by the manufacturer.

5.  Never operate this appliance is not working properly, if it has been dropped or damaged, or dropped into 

water. Return the appliance to a service center for examination and repair. 

6.  Keep the appliance away from heated surfaces.
7.  Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the 

like.

8.  Never drop or insert any object into any opening. 
9.  Do not use outdoors.
10. Do not operate where aerosol (spray) products are being use or where oxygen is being administered. 
11.  The appliance is intended for household use. 

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Fitness Equipment Safety Instructions

CAUTION!! Please be careful when unpacking the carton.

Failure to follow all guidelines may compromise the effectiveness of the exercise experience, expose  

yourself (and possibly others) to injury, and reduce the longevity of the equipment.

Summary of Contents for ERG500 ROWER






















Reviews: