Coax MDU Master Bridge User’s Guide
dir
Show detail file information resides in flash ROM. Include
‘Working Area’ and ‘Upload Area’, refer
Figure 4
. The listed
filenames are,
‘
bootcode
’: bootloader
‘
sysfw
’: system firmware
‘
HcnaMduM
’: Master HCNA driver
‘
HcnaMduEp
’: EP HCNA driver
‘
diagsw
’: utility file for diagnosis
Accompanying file’s date, size, version.
dns
[
-s
<pri/sec> <ip>]
Display or set up DNS server setting.
-s
pri <ip>
: set up Primary DNS server’s IP
-s
sec <ip>
: set up Secondary DNS server’s IP
exit
Close the Telnet console.
quit
Close the Telnet console.
ep
[
-c
<hostcnt>]
[
-n
<note>]
[
-u
<uprate index>]
<mac>
Set up the EP
Properties Profile
related setting values. Use
command
‘upep’
to take effect on EP. (replace the working
values with the setting ones)
<hostcnt>
: EP
Host Limit
setting value (0~255), default
255
<note>
: EP
Note
setting value
<uprate index>
: EP
Up Rate
setting value ( 0~1500, *64Kbps),
default
0
for unlimited
<mac>
: designated EP MAC to configure
filter
[
-s
<set>
[
-c
<act/deact>]
[
-a
<ip>
-m
<mask>]
[
-t
<allow/deny>]
[
-w
<allow/deny>]
[
-n
<allow/deny>]
[
-p
<allow/deny>] ]
Display or set up the filter rule set, refer the section “
Allow
Source
” for IP
<ip>
and Subnet Mask setup
<mask>
.
<set>
: filter set index, total 16 set (0~15)
<act/deact>
: activate or de-activate the rule set
<allow/deny>
: allow or deny the protocol
-t: telnet
-w: http/web
-n: snmp
-p: reply to ICMP ping
help
Display all commands with brief description
hpnareboot
Reset Master HCNA device’
ipconfig
[
-a
<ip>
-m
<mask>
-g
<default gateway>]
Display or set up system IP network, include IP address
<ip>
,
subnet mask
<mask>
, and default gateway
<default gateway>
.
logserver
[
-s
<set>
[
-c
<act/deact>]
[
-a
<ip>
-v
<severity>] ]
Display or set up Unix-like
Syslog
servers(max 5 set)
<set>
: server index, at most 5 servers (0~4)
<act/deact>
: activate or de-activate the server with IP address
<ip>
<severity>
: select the severity level, refer section “
System Log
”,
default level
6
(
info
)
master
-k
<on/off/key
(0x…)
>
Set up Master HCNA device
Privacy Mode and Privacy Key
setting values. Use command
‘upmaster’
to take effect on
Master device. (replace the working values with the setting
ones)
<on/off>
: set ‘Privacy Mode’ to ON or OFF, default
OFF
<key
(0x
nnnn
)
>
,
n
is 0~F: 4-digit ‘Privacy Key’ in hexadecimal,
default
0x0
passwd
[name]
-o
<oldpasswd>
-n
<newpasswd>
Change user’s password, user can update its own password.
Only superuser has the privilege to rewrite other’s password,
[name]
: user’s account name, default to current login name if
not supplied
<oldpasswd>
: old password, superuser can bypass this
parameter
<newpasswd>
: new password
36
www.xtendlan.com
