background image

3

 

IMPORTANT NOTES – ELECTRICAL

•  Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous 

short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are 

always connected securely. Check connectors for if they become loose. And if so, reconnect them securely. 

Never use R/C models with damaged wires. A damaged wire is extremely dangerous, and can cause 

short-circuits resulting in fire. Please have wires repaired at your local hobby shop.

•  Low battery power will result in loss of control. Loss of control can occur due to a weak battery in either 

the transmitter or the receiver. Weak running battery may also result in an out of control car if your car‘s 

receiver power is supplied by the running battery. Stop operation immediately if the car starts to slow 

down.

•  When not using RC model, always disconnect and remove battery. 

•  Do not disassemble battery or cut battery cables. If the running battery short-circuits, approximately 

300W of electricity can be discharged, leading to fire or burns. Never disassemble battery or cut battery 

cables.

•  Use  a  recommended  charger  for  the  receiver  and  transmitter  batteries  and  follow  the  instructions 

correctly. Over-charging, incorrect charging, or using inferior chargers can cause the batteries to become 

dangerously hot. Recharge battery when necessary. Continual recharging may damage battery and, in 

the worst case, could build up heat leading to fire. If battery becomes extremely hot during recharging, 

please ask your local hobby shop for check and/or repair and/or replacement.

•  Regularly check the charger for potential hazards such as damage to the cable, plug, casing or other 

defects. Ensure that any damage is rectified before using the charger again. Modifying the charger may 

cause short-circuit or overcharging leading to a serious accident. Therefore do not modify the charger.

•  Always unplug charger when recharging is finished.

•  Do not recharge battery while battery is still warm. After use, battery retains heat. Wait until it cools 

down before charging. 

•  Do not allow any metal part to short circuit the receiver batteries or other electrical/electronic device on 

the model.

•  Immediately stop running if your RC model gets wet as may cause short circuit. 

•  Please dispose of batteries responsibly. Never put batteries into fire.

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and workmanship within 30 days 

of purchase. The total monetary value under warranty will in no case exceed the cost of the original kit 

purchased. This warranty does not cover any components damaged by use or modification or as a result 

of wear. Part or parts missing from this kit must be reported within 30 days of purchase. No part or parts 

will be sent under warranty without proof of purchase. Should you find a defective or missing part, contact 

the local distributor. Service and customer support will be provided through local hobby store where you 

have purchased the kit, therefore make sure to purchase any XRAY products at your local hobby store. 

This model racing car is considered to be a high-performance racing vehicle. As such this vehicle will be 

used in an extreme range of conditions and situations, all which may cause premature wear or failure of 

any component. XRAY has no control over usage of vehicles once they leave the dealer, therefore XRAY 

can only offer warranty against all manufacturer‘s defects in materials, workmanship, and assembly at 

point of sale and before use. No warranties are expressed or implied that cover damage caused by what is 

considered normal use, or cover or imply how long any model cars‘ components or electronic components 

will last before requiring replacement.

Due to the high performance level of this model car you will need to periodically maintain and replace 

consumable  components.  Any  and  all  warranty  coverage  will  not  cover  replacement  of  any  part  or 

component  damaged  by  neglect,  abuse,  or  improper  or  unreasonable  use.  This  includes  but  is  not 

limited to damage from crashing, chemical and/or water damage, excessive moisture, improper or no 

maintenance, or user modifications which compromise the integrity of components. Warranty will not 

cover components that are considered consumable on RC vehicles. XRAY does not pay nor refund shipping 

on any component sent to XRAY or its distributors for warranty. XRAY reserves the right to make the final 

determination of the warranty status of any component or part.

Limitations of Liability

XRAY makes no other warranties expressed or implied. XRAY shall not be liable for any loss, injury or 

damages, whether direct, indirect, special, incidental, or consequential, arising from the use, misuse, or 

abuse of this product and/or any product or accessory required to operate this product. In no case shall 

XRAY‘s liability excess the monetary value of this product.

Take adequate safety precautions prior to operating this model. You are responsible for this 

model’s assembly and safe operation.

Disregard of the any of the above cautions may lead to accidents, personal injury, or property 

damage.  XRAY  MODEL  RACING  CARS  assumes  no  responsibility  for  any  injury,  damage,  or 

misuse of this product during assembly or operation, nor any addictions that may arise from 

the use of this product.

All rights reserved

.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best compounds for molded parts 

and the most sophisticated manufacturing processes of TQM (Total Quality Management). We guarantee 

that all parts of a newly-purchased kit are manufactured with the highest regard to quality. However, due 

to the many factors inherent in model racecar competition, we cannot guarantee any parts once you start 

racing the car. Products which have been worn out, abused, neglected or improperly operated will not be 

covered under warranty. 

We wish you enjoyment of this high-quality and high-performance RC car and wish you best success on the 

track!

In line with our policy of continuous product development, the exact specifications of the kit may vary. In the unlikely event 

of any problems with your new kit, you should contact the model shop where you purchased it, quoting the part number.

We do reserve all rights to change any specification without prior notice. All rights reserved.

R/C & BUILDING TIPS

• Make sure all fasteners are properly tightened. Check them periodically.

• Make sure that chassis screws do not protrude from the chassis.

• For the best performance, it is very important that great care is taken to ensure the free movement of all 

parts.

• Clean all ball-bearings so they move very easily and freely.

• Tap or pre-thread the plastic parts when threading screws.

• Self-tapping screws cut threads into the parts when being tightened. Do not use excessive force when 

tightening the self-tapping screws because you may strip out the thread in the plastic. We recommended 

you stop tightening a screw when you feel some resistance.

• Ask your local hobby shop for any advice.

Please support your local hobby shop. We at XRAY Model Racing Cars support all local hobby dealers. 

Therefore we ask you, if at all possible, to purchase XRAY products at your hobby dealer and give them 

your support like we do. If you have difficulty finding XRAY products, please check out www.teamxray.com to 

get advice, or contact us via email at [email protected], or contact the XRAY distributor in your country.

Summary of Contents for XB2D 2019













































Reviews: