background image

1

DISTRIBUTED EXCLUSIVELY BY

Global Hobby Distributors

18480 Bandilier Circle, Fountain Valley, CA  92708

All contents copyright © 2005, Global Hobby Distributors

Version V1.0  May 2005

Kit Product # 145619

OPERATION, TUNING GUIDE AND REPLACEMENT PARTS

MAMMOTH ST NITRO STADIUM TRUCK FEATURES:

Factory-Built and Painted

Powerful XTM Racing 24.7 Engine with Tuned Pipe

Hitec Aggressor AM Radio System

High-Torque Metal Gear Steering Servo

2-Speed Transmission for Awesome Speed

Low Center of Gravity for Awesome Handling

Double Bracing Front and Rear

New Upper Arm Design for More Precise Handling

Full Ball Bearings

Heavy-Duty Side Dust Guards

3mm Aluminum Chassis with Curved Edges for Added Strength

Large Front Bumper and Skid Plate

Triple Vented Disc Brakes

Chrome-Plated Universals and Dogbones for Added Strength

Steel Differentials

Gear Boxes Allow Easy Differential Removal

3.5mm Rear Sway Bar

Fully Threaded, Oil-Filled Aluminum Shocks with 3.5mm Shafts

Dish-Style Racing Wheels with 17mm Hex Mounts

Factory-Glued Tires with Inserts

Adjustable Camber, Caster and Toe-In Front and Rear

Water Resistant Receiver and Battery Boxes

IMPORTANT

  Before operating your new XTM Racing Mammoth ST

Nitro Stadium Truck, please read and understand the warnings listed on
the next page.  Failure to do so could lead to bodily harm and/or injury.

The XTM Racing Mammoth ST Nitro Stadium Truck is not intended for
persons under 12 years of age, unless closely supervised by an adult.

I

NCLUDES

 H

ITEC

 A

GGRESSOR

 R

ADIO

 

AND

 P

OWERFUL

 XTM 24.7 E

NGINE

!

Summary of Contents for Mammoth ST

































































Reviews: