Xray T2008 Instruction Manual Download Page 3

3

 IMPORTANT NOTES – ELECTRICAL

•  Insulate any exposed electrical wiring (using heat shrink tubing or electrical 

tape) to prevent dangerous short circuits. Take maximum care in wiring, 
connecting and insulating cables. Make sure cables are always connected 
securely. Check connectors for if they become loose. And if so, reconnect 
them securely. Never use R/C models with damaged wires. A damaged wire 
is extremely dangerous, and can cause short-circuits resulting in fire. Please 
have wires repaired at your local hobby shop.

•  Low battery power will result in loss of control. Loss of control can occur due to 

a weak battery in either the transmitter or the receiver. Weak running battery 
may also result in an out of control car if your car‘s receiver power is supplied 
by the running battery. Stop operation immediately if the car starts to slow 
down.

•  When not using RC model, always disconnect and remove battery. 
•  Do not disassemble battery or cut battery cables. If the running battery short-

circuits, approximately 300W of electricity can be discharged, leading to fire 
or burns. Never disassemble battery or cut battery cables.

• Use a recommended charger for the receiver and transmitter batteries 

and follow the instructions correctly. Over-charging, incorrect charging, or 
using inferior chargers can cause the batteries to become dangerously hot. 

Recharge battery when necessary. Continual recharging may damage battery 
and, in the worst case, could build up heat leading to fire. If battery becomes 
extremely hot during recharging, please ask your local hobby shop for check 
and/or repair and/or replacement.

•  Regularly check the charger for potential hazards such as damage to the 

cable, plug, casing or other defects. Ensure that any damage is rectified 
before using the charger again. Modifying the charger may cause short-circuit 
or overcharging leading to a serious accident. Therefore do not modify the 
charger.

•  Always unplug charger when recharging is finished.
•  Do not recharge battery while battery is still warm. After use, battery retains 

heat. Wait until it cools down before charging. 

•  Do not allow any metal part to short circuit the receiver batteries or other 

electrical/electronic device on the model.

•  Immediately stop running if your RC model gets wet as may cause short 

circuit. 

•  Please dispose of batteries responsibly. Never put batteries into fire.

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and 
workmanship within 30 days of purchase. The total monetary value under 
warranty will in no case exceed the cost of the original kit purchased. This 
warranty does not cover any components damaged by use or modification or 
as a result of wear. Part or parts missing from this kit must be reported within 
30 days of purchase. No part or parts will be sent under warranty without proof 
of purchase. Should you find a defective or missing part, contact the local 
distributor. Service and customer support will be provided through local hobby 
store where you have purchased the kit, therefore make sure to purchase any 
XRAY products at your local hobby store. This model racing car is considered 
to be a high-performance racing vehicle. As such this vehicle will be used in 
an extreme range of conditions and situations, all which may cause premature 
wear or failure of any component. XRAY has no control over usage of vehicles 
once they leave the dealer, therefore XRAY can only offer warranty against all 
manufacturer‘s defects in materials, workmanship, and assembly at point of 
sale and before use. No warranties are expressed or implied that cover damage 
caused by what is considered normal use, or cover or imply how long any 
model cars‘ components or electronic components will last before requiring 
replacement.

Due to the high performance level of this model car you will need to periodically 
maintain and replace consumable components. Any and all warranty coverage 
will not cover replacement of any part or component damaged by neglect, 
abuse, or improper or unreasonable use. This includes but is not limited to 

damage from crashing, chemical and/or water damage, excessive moisture, 
improper or no maintenance, or user modifications which compromise the 
integrity of components. Warranty will not cover components that are considered 
consumable on RC vehicles. XRAY does not pay nor refund shipping on any 
component sent to XRAY or its distributors for warranty. XRAY reserves the right to 
make the final determination of the warranty status of any component or part.

Limitations of Liability

XRAY makes no other warranties expressed or implied. XRAY shall not be liable 
for any loss, injury or damages, whether direct, indirect, special, incidental, or 
consequential, arising from the use, misuse, or abuse of this product and/or any 
product or accessory required to operate this product. In no case shall XRAY‘s 
liability excess the monetary value of this product.

Take adequate safety precautions prior to operating this model. You 
are responsible for this model’s assembly and safe operation.

Disregard of the any of the above cautions may lead to accidents, 
personal injury, or property damage. XRAY MODEL RACING CARS 
assumes no responsibility for any injury, damage, or misuse of this 
product during assembly or operation, nor any addictions that may 
arise from the use of this product.
All rights reserved.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best 
compounds for molded parts and the most sophisticated manufacturing processes 
of TQM (Total Quality Management). We guarantee that all parts of a newly-
purchased kit are manufactured with the highest regard to quality. However, due 
to the many factors inherent in model racecar competition, we cannot guarantee 

any parts once you start racing the car. Products which have been worn out, 
abused, neglected or improperly operated will not be covered under warranty. 
We wish you enjoyment of this high-quality and high-performance RC car and 
wish you best success on the track!

In line with our policy of continuous product development, the exact specifications of the kit may 
vary. In the unlikely event of any problems with your new kit, you should contact the model shop 
where you purchased it, quoting the part number.
We do reserve all rights to change any specification without prior notice. All rights reserved.

R/C & BUILDING TIPS

• Make sure all fasteners are properly tightened. Check them periodically.
• Make sure that chassis screws do not protrude from the chassis.
• For the best performance, it is very important that great care is taken to ensure 

the free movement of all parts.

• Clean all ball-bearings so they move very easily and freely.
• Tap or pre-thread the plastic parts when threading screws.
• Self-tapping screws cut threads into the parts when being tightened. Do not use 

excessive force when tightening the self-tapping screws because you may strip 
out the thread in the plastic. We recommended you stop tightening a screw 
when you feel some resistance.

• Ask your local hobby shop for any advice.

Please support your local hobby shop. We at XRAY Model Racing Cars support 
all local hobby dealers. Therefore we ask you, if at all possible, to purchase 
XRAY products at your hobby dealer and give them your support like we do. If 
you have difficulty finding XRAY products, please check out www.teamxray.com 
to get advice, or contact us via email at [email protected], or contact the XRAY 
distributor in your country.

Summary of Contents for T2008

































Reviews: