background image

8

RIdE HEIGHT - THEORY

Ride height is the height of the chassis in relation to the surface it is sitting on, with the car ready to run. Ride height affects the car’s traction since it 

alters the car’s center of gravity and roll center. Because of changes in suspension geometry and ground clearance, there are negative consequences 

to altering ride height too much. 

Measure and adjust ride height with the car ready-to-run but without the body. Use the shock preload collars to raise and lower the ride height. 

RIdE HEIGHT - EFFEcTS OF adJUSTMENT

rIDe HeIGHT AnD TIreS

 

Ride  height  is  measured  with  the  wheels  on  the  car,  and  the  car  ready-to-run.  When  using  rubber  tires,  your  ride  height  settings  should  stay 

consistent, since rubber tires do not wear down appreciably during use, which results in a fairly constant ride height. However, if using foam tires, 

the car’s ride height decreases as the foam tires wear down to smaller diameters. Please see the tips for using foam tires.

 

rIDe HeIGHT AnD SUSpenSIOn SeTTInGS

 

Suspension settings are unaffected by the wheels/tires you put on the car, only the ride height is affected. When you use a set-up system (such as 

the HUDY All-In-One Set-Up Solution) to set your suspension settings, the suspension settings do not change when you put different wheels on the 

car. With the car sitting on the ground, it may appear that certain settings are different, but this may be due to uneven tires, or tires with different 

diameters. However, the settings you set using a set-up system are the true suspension settings.

RIdE HEIGHT - MEaSURING

InITIAl STepS

SeT-Up cOmpOnenTS

prepare the car as follows:

Use the following set-up components:

· 

Shocks: Attach the front and rear shocks

· 

Anti-roll bars: Attach front and rear anti-roll bars

· 

Wheels: Attach the wheels.  Both left and right wheels at the front or rear should be  

   the same diameter 

· 

Ride Height Gauge

Decreasing ride height 

(lowering the car)

· 

Increases overall grip.

· 

Better on smooth tracks.

Increasing ride height 

(raising the car)

· 

Decreases overall grip.

· 

Better on bumpy tracks (prevents bottoming).

RIDE HEIGHT

ride height front

ride height rear

Summary of Contents for T2













































Reviews: