background image

43

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and 
workmanship within 30 days of purchase. The total monetary value under 
warranty will in no case exceed the cost of the original kit purchased. This 
warranty does not cover any components damaged by use or modifi cation 
or as a result of wear. Part or parts missing from this kit must be reported 
within 30 days of purchase. No part or parts will be sent under warranty 
without proof of purchase. Should you fi nd a defective or missing part, 
contact the local distributor. Service and customer support will be provided 
through local hobby store where you have purchased the kit, therefore make 
sure to purchase any XRAY products at your local hobby store. This model 
racing car is considered to be a high-performance racing vehicle. As such 
this vehicle will be used in an extreme range of conditions and situations, all 
which may cause premature wear or failure of any component. XRAY has 
no control over usage of vehicles once they leave the dealer, therefore XRAY 
can only offer warranty against all manufacturer‘s defects in materials, 
workmanship, and assembly at point of sale and before use. No warranties 
are expressed or implied that cover damage caused by what is considered 
normal use, or cover or imply how long any model cars‘ components or 
electronic components will last before requiring replacement.

Due to the high performance level of this model car you will need to 
periodically maintain and replace consumable components. Any and all 
warranty coverage will not cover replacement of any part or component 
damaged by neglect, abuse, or improper or unreasonable use. This 

includes but is not limited to damage from crashing, chemical and/or 
water damage, excessive moisture, improper or no maintenance, or user 
modifi cations which compromise the integrity of components. Warranty will 
not cover components that are considered consumable on RC vehicles. 
XRAY does not pay nor refund shipping on any component sent to XRAY 
or its distributors for warranty. XRAY reserves the right to make the fi nal 
determination of the warranty status of any component or part.

Limitations of Liability

XRAY makes no other warranties expressed or implied. XRAY shall not be 
liable for any loss, injury or damages, whether direct, indirect, special, 
incidental, or consequential, arising from the use, misuse, or abuse of this 
product and/or any product or accessory required to operate this product. 
In no case shall XRAY‘s liability excess the monetary value of this product.

Take adequate safety precautions prior to operating this model. You 
are responsible for this model’s assembly and safe operation.

Disregard of the any of the above cautions may lead to accidents, 
personal injury, or property damage. XRAY MODEL RACING CARS 
assumes no responsibility for any injury, damage, or misuse of 
this product during assembly or operation, nor any addictions 
that may arise from the use of this product. All rights reserved.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best 
compounds for molded parts and the most sophisticated manufacturing processes 
of TQM (Total Quality Management). We guarantee that all parts of a newly-
purchased kit are manufactured with the highest regard to quality. However, due 
to the many factors inherent in model racecar competition, we cannot guarantee 

any parts once you start racing the car. Products which have been worn out, 
abused, neglected or improperly operated will not be covered under warranty. 
We wish you enjoyment of this high-quality and high-performance RC car and 
wish you best success on the track!

Summary of Contents for NT18











































Reviews: