Xray NT1 Instruction Manual Download Page 40

Page: 40 / 48

NOTE

ORIENTATION

981212

P 2x12

902308

SH M3x8

903308

SFH M3x8

901303

SB M3x3

902310

SH M3x10

902306

SH M3x6

Screw from servo

6mm THREAD

8mm THREAD

Insert rod through hole in brake

arm. Bend rod to proper shape.

OPTIONAL:

#331216 Graphite Upper

Holder for Bumper 2.5mm

OPTIONAL:

#331221 Foam Bumper for

Anti-Roll Bar - Hard - V2

OPTIONAL:

#334061-O Alu Brake Post

Arm - Swiss 7075 T6 - Orange

CARB LINKAGE & BODYMOUNTS

Approx.15mm

Do not overtighten

screws; pivots must

rotate freely

Thread

HUDY ALU SERVO HORNS

#293494 23T KO Propo, Airtronics, JR, Sanwa (OPTION)
#293495 24T Hitec (OPTION)
#293496 25T Futaba (OPTION)

Use appropriate
servo arm:

- (23T)

- (24T)

- (25T)

6.3mm

IMPORTANT:

It is important to have the exact

length of the linkage. Too long

or too short link will cause the

chassis bend and unwanted

tweak problems. To check that

the legth is correct, composite

balls must move freely.

6mm THREAD

8mm THREAD

REAR BODY MOUNTS

301332 0mm

STANDARD

1mm STANDARD
2mm OPTION

THREAD LOCK

Summary of Contents for NT1

















































Search results

Summary of Contents for NT1

Reviews:

Brands by name

Popular brands

Xray NT1, Instruction Manual

Search results

Summary of Contents for NT1

Reviews:

Brands by name

Popular brands