5 6
●
OPERATION INSTRUCTION:
Note: When the product is plugged in a double ‘BEEP’ sound will confirm that the
product is correctly connected to the mains supply and the product is in STANDBY
MODE.
Note: The product will not start to operate until you press the “ON/OFF”
button
CONTROL BUTTONS
1) ON/OFF BUTTON
To start the product from STANDBY MODE you must press the “ON/OFF” button.
You will hear a single ‘BEEP’ sound when you have successfully pressed the
button, the first time you start the product from Standby it will start to operate with
the fan running at “LOW” speed, in Normal Mode, in non-oscillation mode and with
the appropriate LED light symbols light up on the display.
The fan will work in the same status with that before it turned off without shut off,
except Timer and Mode function. You can change the mode of operation by using
the other control buttons as described below.
To turn off the product and return to Standby mode from any mode of operation just
press the ON/OFF button, you will hear a long ‘Beep’ sound to confirm switch
operation.
NOTE: As long as you leave the product in Standby Mode and do not disconnect at
the mains the product will remember the fan speed and the oscillation mode that
you had last set before you switched it off, so when you switch it on again from
Standby mode it will start in the fan speed mode and oscillation mode that it was
last used in.
2) FAN SPEED SELECTION BUTTON
Default Blower Mode is Normal Mode, you can set your product to work at 3
different fan speeds in Normal mode - Low, Medium & High. Pressing the
button allows you to change from Low to Medium, Medium to High and High back
to Low fan speed , the relevant LED light will illuminate to indicate which fan speed
is selected/operating.
3) RUNBACK TIMER MODE BUTTON
By pressing this button, the fan can be set to operate continuously in your selected
mode of operation for different time intervals, you can select 1 hour, 2 hours, 4
hours or 8 hours, the selected period will be indicated by its LED light which will
remain on for the selected period, when the selected operating time has run out the
product will switch off automatically and go into standby mode until the user needs
it again.
4)
4)
4)
4)
BLOWER MODE SELECTION BUTTON
The default operating mode when you power on is ‘Normal’ mode, there is no
separate ‘Normal’ blower mode operating LED. Pressing
when operating will
change the blower operation modes from ‘Normal’ to ‘Sleep’ mode, ‘Sleep’ to
‘Natural’ mode, ‘Natural’ to ‘ECO’ mode and ‘ECO’ back to Normal mode, the
relevant LED light will indicate when Sleep, Natural and ECO modes are selected,
(the selected fan speed LED will only light in Normal Blower mode).
A. Normal Blower mode:
See ‘FAN SPEED SELECTION BUTTON’ section for details of operation in this
default mode.
B. Sleep Blower Mode: In this mode the fan speed
will continuously vary speed to
prevent users from getting sick when asleep. You can select 3 different running
patterns in this mode by using the Speed Selection button, the patterns of
operation in each speed mode are as follows;
- High speed: Operates for 30 minutes in ‘High speed in Natural Blower mode’
→
30
minutes at ‘Medium speed in Natural Blower mode’
→
then continues in ‘Low
speed in Natural Blower mode’:
- Medium speed: Operates for 30 minutes in ‘Medium speed in Natural Blower
mode’
→
then continues to run in ‘Low speed in Natural Blower mode’.
- Low speed
：
Operates continuously in ‘Low speed in Natural Blower mode’.
C. Natural Blower mode
：
In this mode the fan will automatically change speed to
simulate natural variances in the speed of the wind that you experience outside in
natural windy conditions. In this mode you can use the speed selection button to
change between Low/‘/Light breeze’, Middle/‘Strong Breeze’ and High/‘Strong
Wind’ modes.
