background image

We thank you for purchasing Vehicle Satellite Receiver System. 
 
 GENERAL 

 

Motosat  (Vehicle  Satellite  Receiver  System)  is  designed  to  be  used  for  receiving  and 
watching  satellite  broadcasting  in  road  vehicles  like  passenger,  coaches,  caravans, 
minibuses, trucks and lorries while these vehicles are at park position.

 

 

 IMPORTANT SAFETY INSTRUCTIONS 

 

Do not open the cover of the unit. No user-serviceable parts inside. To open the covers 
cancels the guarantee of the unit. Refer to authorized technical service. 
 
Installation  of  the  system  should  be  done  by  authorized  technical  service.  Installation 
made  by  unauthorized  person  cancels  the  guarantee.  Such  a  case  is  also  risky  for 
safety of lives and vehicle. 
 
There  is  a  “CONTACT”  input  in  the  Controlbox.  This  input  should  be  connected  to  a 
supply  voltage. When  motor  of  the  vehicle  is  switched  on,  system  detects  it  and  shuts 
down antenna and the receiver unit switches off itself automatically.   
 
This system is not suitable for using while the vehicle in motion. Using during drive may 
cause damage to the vehicle as well as it will be dangerous for life safety. 
 
The system shuts down itself and closes the antenna automatically when the vehicle is 
operated,  but  checking  on  whether  the  antenna  is  closed  or  not,  before  moving,  is 
important for a safe journey. 
 
The Controlbox is designed for installing into the dashboard of the vehicle. If dashboard 
installation  is  not  possible,  while  determining  the  installation  place  of  the  controlbox, 
make sure that the heat is not very high. Over heat may cause dangerous situations. 
 
If the antenna is covered by snow or ice, do not operate the system. That kind of usage 
may cause permanent damages to the system. 
 
Do  not  connect  any  unapproved  equipment  to  prevent  your  unit  against  a  permanent 
damage or danger. 
 
The antenna part of the system, which is installed on top of the vehicle, causes a height 
on  the  vehicle.  Make  sure  that  this  height  will  not  cause  any  risk  while  cruising  you’re 
your vehicle. It is very important that to be aware of this height for safety while crossing 
a bridge, crossover or wooded road. 
 
Official  actions  in  accordance  with  legislations  about  the  antenna  part  of  the  system, 
which is mounted top of the vehicle, are under user responsibility. 

Summary of Contents for MTA 65 Series














Reviews: