background image

3

EN

Thema: 

Safety instructions and precautions

Safety instructions and 
precautions

!

 Handling by stop only

To avoid any accidents please don't 
handle the unit while you driving. Please 
stop and park the vehicle at safety 
place and handle the unit casually.

!

 Installation

Please read the following manual 
carefully before you install the unit. We 
recommend you to let the technician 
install the unit in your vehicle.

!

 Regular loudness

Please set the loudness of the unit to 
the appropriate level so you were still 
able to hear exterior noises especially 
traffic warning signals. Furthermore the 
higher loudness level can damage your 
hearing organs.

!

 Repair of the unit

Do not open the unit. Do not try to 
repair the unit by yourself due to any 
emerging technical problems. While 
opening the unit by yourself exists the 
danger to be electrocuted. 

Do not use the unit any further since 
you detect any kind of technical 
problems. 

Leave all the repair operations to 
professional technicians.

 

Due to flawed warranty seal the 

warranty becomes invalid.

!

 Power supply

Use the unit connected only to 12 Volt 
on-board power supply. The minus (-) 
should be connected with the ground 
(GND) (negative).

 

 

Due to the wrong configuration exists 
the danger of fire. In case of doubt 
please consult with professional techni

-

cians.

!

 Replacement of fuses

While replacing the fuse please make 
sure that the new fuse has the same 
properties as the old one, especially the 
amperage.

!

 Overheating

Do not occlude the vent holes to avoid 
the heat generation and accumulation 
in the unit. Otherwise exists the danger 
of fire.

!

 Regular temperature

Please make sure that the temperature 
inside of the vehicle amounts to not 
more than +40 C. 

If it's too cold or too hot inside of the 
vehicle, do not turn the unit on until 
the inside temperature of the cabin 
descends.

!

Summary of Contents for XM-01Z























Reviews: