background image

www.xolta.com

7

 

 

Safe disposal of Lithium-ion batteries

 

Uninstalling a XOLTA battery should only be undertaken by an authorized electrician. 

 

Lithium-ion batteries must be treated as hazardous waste and not be disposed of with regular waste.

 

Special regulations apply to the transport of batteries, and these must always be observed.

 

A XOLTA battery that has reached the end of its functional life can be returned to the seller that originally  

 

sold the battery or to the dealer of a new industrial battery.

 

Disclaimer

 

We have taken every precaution to ensure that all information provided in this installationguide is correct and up to 

 

 

date. However, we assume no responsibility for damage to persons and property arising as a result of following 

 

 

recommendations and/or procedures described in this Guide. Furthermore, we assume no responsibility 

 

 

for any infringements of rights of third parties which may result from the use of this Guide.

 

The system is designed to assure that an installed XOLTA Outdoor BESS and all its associated functionalities  

 

behave safely under the predefined operating conditions. Nevertheless, please read all sections describing 

 

 

safety issues and precautions carefully before installation, operation, or performing service work on a XOLTA 

 

 

Outdoor BESS. Failure to do so could result in reduced system performance, damage to the system, personal 

 

 

injury or even death.

 

   

Cyber security

 

   

The XOLTA BAT-80 Outdoor BESS connects to local communications networks outside the control of

 

 

   

XOLTA. It is therefore the user’s sole responsibility to ensure that all appropriate measures are taken

 

 

   

to mitigate any unauthorized access to or interference with the product that can result in misuse or theft

 

 

   

of data. XOLTA and its affiliates are not liable for damages or losses related to such security breaches.

 

 

Copyright

 

This document and all information contained in the XOLTA User Manual are copyright 2022 by XOLTA A/S. 

 

 

All rights reserved. XOLTA reserves the right to make changes to the products described in this manual at 

 

 

any time without notice. This manual may be photocopied or otherwise distributed only to the extent that is 

 

 

necessary for the correct operation and installation of XOLTA Outdoor BESS.

 

Voiding of warranty

NOTE!

 

Please refer to XOLTA’s Terms and Conditions document delivered by XOLTA which governs the term and 

 

 

conditions for the product warranty.

 

The warranty for the product does not apply to, and XOLTA will not be responsible for, any defect, loss or 

 

 

damage to any product caused if:

 

•  The product covered is not continuously connected to the internet via LAN cable, meaning that XOLTA  

 

  cannot monitor the performance of said product;

 

•  The product covered has not been stored, transported, set up or installed in an appropriate and professional  

 

  manner in accordance with technical standards and regulations, in accordance with the relevant installation 

 

 

  manual of the product or the instructions of XOLTA;

 

•  The product covered has been operated contrary to its intended use or contrary to the instructions in the  

 

  relevant installation manual;

 

•  The product covered was out of service for a continuous period of more than six months after the initial 

 

 

  installation due to the fault of the purchaser;

 

•  The product covered has not been serviced properly and professionally according to technical standards  

 

  or XOLTA’s maintenance instructions;

Summary of Contents for BAT-80


























Reviews: