background image

Please read through completely before using your XO Unit

To prevent damage to the door gasket, the door must be opened all the way before pulling shelves out.

The appliance must be positioned so that the plug is accessible.  

Empty your XO unit before attempting to move the appliance.  Moving while loaded may damage or

distort the frame. 
The compressor will get HOT during operation / touching it may cause injury.

 

During installation follow all safety tips provided in this manual / appropriate safety equipment such as 

safety glasses and work gloves should be worn.

Two people should move or lift your XO unit to prevent injury or damage.  

Remove all interior and exterior packing materials prior to installation and dispose of properly.

Never cover the bottle racks with foil or other material which will impede internal air circulation.

For maximum efficiency, keep the door tightly shut unless loading or unloading and never overload your 

XO unit.

Before installing, allow your XO unit to sit upright for 2 hours at the install site.  This will allow the cooling 

system to stabilize after transportation.  Failure to follow this step may cause problems.

Location

Your XO unit should be located away from direct sunlight and heat sources (stove, heaters, etc.) which may 

increase electrical consumption.  High or low ambient temperature may cause units to work improperly.

The floor must be strong enough to support your XO unit fully loaded.

Your XO unit must not be installed in areas of where water or excessive moisture are present.

Your XO unit’s final installation must observe the correct minimum air clearances around and behind the

unit to ensure adequate ventilation.  In addition, all ventilation openings must be kept clear and free of

obstructions, failure to do so will result in damage to the unit.

WARNING

NEVER use external heat sources to accelerate defrosting

NEVER permit unauthorized service or modifications to your XO unit 

NEVER tamper with the sealed refrigerant system - this unit uses R600A Refrigerant which is flammable.

It should never be used in the vicinity of any flammable or explosive ignition sources.

ALWAYS FOLLOW THE ELECTRICAL SAFETY INSTRUCTIONS OUTLINED IN THIS MANUAL.   

    

 

6

your safety matters

Never store perishable food products such as meat or cheese in your wine cooler or beverage center. 

Your XO unit must not be installed near where flammable, corrosive or hazardous materials are present. 

Summary of Contents for XOU24BCGO Series

























Reviews: