XMA Viglen Omnino Pro Assembly Manual Download | Manualshive

Page: 41 / 60

background image

0115 846 4000

[email protected]

© 2019 XMA Ltd. All Rights Reserved

15.1 Replacing the Internal Power board

Procedure

1.  Align the power board with the screw holes on the system board.
2.  Tighten the screws that secure the power board to chassis.
3.  Carefully cover the power board with mylar.
4.  Connect the outlet power connector and tighten the two screws.
5.  Connect the 19V 4Pin converter to 2Pin DC connector to system board.

NOTE: Please ensure 4Pin converter to 2Pin DC cable is used, this cable should not be discarded.
When replacing the power module transfer the 4pin to 2pin DC cable to new mower module.

«
...
39
40
41
42
43
...
»

Summary of Contents for Viglen Omnino Pro





























































Reviews:

No comments

Related manuals for Viglen Omnino Pro

Brand: Radio Shack Pages: 31

Brand: Kaypro Pages: 157

Brand: CompuLab Pages: 19

Brand: Acer Pages: 24

Brand: qian.mx Pages: 68

6862 - PC 300 PL

Brand: IBM Pages: 208

Brand: eMachines Pages: 406

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 7

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 4

T-Series T3100e

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 26

Tecra A3 Series

Brand: Toshiba Pages: 64

Brand: Toshiba Pages: 130

Brand: Toshiba Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands