11
Normal mode HSI
Compact mode HSI
DMX ch
Function
Decimal
Percent
Description
1
Reset
0 - 249
250 -255
0 - 97
98 - 100
Reserved for special functions
Hold for 5 seconds to reset the Droplet
TM
2
Pan
0 - 255
0 - 100
Position from 0° - 360°
3
Tilt
0 - 255
0 - 100
Position from 0° - 260°
4
Strobe
Frequency
0 - 4
5 - 204
205 - 255
0 - 2
3 - 80
81 - 100
Full on, no strobe
Strobe linear from 1Hz to 25Hz
Strobe linear from 25Hz to 50Hz
5
Hue
0
1 - 42
43
44 - 84
85
86 - 127
128
129 -170
171
172 - 212
213
214 - 254
255
0
1 - 16
17
18 - 32
33
34 - 49
50
51 - 66
67
68 - 82
83
84 - 99
100
Primary colors if Saturation channel has value 255
Red
Red <> Yellow
Yellow
Yellow <> Green
Green
Green <> Cyan
Cyan
Cyan <> Blue
Blue
Blue <> Magenta
Magenta
Magenta <> Red
Red
6
Saturation
0 - 255
0 - 100
Linear fading from white to saturated color chosen via
the Hue channel
7
Intensity
0 - 255
0 - 100
Linear fading from 0 – 100% output
DMX ch
Function
Decimal
Percent
Description
1
Reset
0 - 249
250 -255
0 - 97
98 - 100
Reserved for special functions
Hold for 5 seconds to reset the Droplet
TM
2
Pan
0 - 255
0 - 100
Position from 0° - 360°
3
Tilt
0 - 255
0 - 100
Position from 0° - 260°
4
Speed
0
255
0 - 100
Full speed of pan and tilt movement
Slowest pan and tilt movement
5
Pan fine
0 - 255
0 - 100
Fine Positioning of the pan within an angle of 1,41°
6
Tilt fine
0 - 255
0 - 100
Fine Positioning of the tilt within an angle of 1,02°
7
Strobe
Frequency
0 - 4
5 - 204
205 - 255
0 - 2
3 - 80
81 - 100
Full on, no strobe
Strobe linear from 1Hz to 25Hz
Strobe linear from 25Hz to 50Hz
8
Strobe
Duration
0 - 255
0 - 100
Linear from 0 – 100% with steps of 1,6%
9
Hue
0
1 - 42
43
44 - 84
85
86 - 127
128
129 -170
171
172 - 212
213
214 - 254
255
0
1 - 16
17
18 - 32
33
34 - 49
50
51 - 66
67
68 - 82
83
84 - 99
100
Linear fading through all saturated colors if the
Saturation channel has value 255
Red
Red <> Yellow
Yellow
Yellow <> Green
Green
Green <> Cyan
Cyan
Cyan <> Blue
Blue
Blue <> Magenta
Magenta
Magenta <> Red
Red
10
Saturation
0 - 255
0 - 100
Linear fading from white to saturated color chosen via
the Hue channel
11
Intensity
0 - 255
0 - 100
Linear fading from 0 – 100% output
12
2.3.
Accessories
Standard supplied
Lenses
When delivered the has a beam angle of 10°. Additional supplied with each Droplet
TM
are two lenses,
one with a beam angle of 18° and the other with a beam angle of 30°.
Replacing a lens
To replace a lens of the Droplet
TM
first take of the front hood by pulling the front hood. The existing lens
or lens dome can be taken out. When you want to have a larger beam angle and the lens dome take
out the black synthetic ring. Than first place the 18° or 30° lens and than the lens dome. The lenses
should be placed with the uncurved side pointing to the Droplet
TM
and the curved side to the outside.
Extension shaft
The head of the Droplet
TM
can be taken of of the base and can be extended this way. Xilver B.V.
supplies optional extension shafts for this purpose.
The following sizes of extension shafts can be delivered out of stock:
?
15cm (5,91inch)
?
25cm (9,84inch)
?
35cm (13,78inch)
Other sizes can be delivered on request.
The extension shaft is standard colored in silver (RAL 9006), black (RAL 9005) or white (RAL 9003).
On request it can be delivered in any RAL color or even in custom color.
Warning:
A Droplet
TM
with extension shaft may only operate hanging (max. extension length: 55cm /
21.65inch) in vertical direction or standing (max. extension length: 20cm / 7.87inch).
Cables
The Droplet
TM
is standard delivered without cables and connectors. On request the Droplet
TM
can be
pre-wired with Data and power cable with the desired connector.
2.4. Place of usage
The Droplet
TM
is mentioned for indoor use only! The product may not be exposed to water or extreme
hot or cold environments.
The Droplet
TM
should not be used in humid environments. The minimum operation temperature of the
Droplet
TM
is 0°C (32°F) and the maximum is 40°C (104°F). The minimum storage temperature of the
Droplet
TM
is -10°C (14°F) and the maximum is 60°C (140°F).
In case of building-in the base of the Droplet
TM
make sure there is enough ventilation so the unit
becomes not overheated.
Should the Droplet
TM
get overheated in case of a too high environment temperature or not enough
ventilation, the Droplet
TM
will limit its light output to protect the LEDs.
Warning:
during the use of the Droplet
TM
make sure that no persons or objects get in contact with the
unit in a direct way. The pan and tilt travel should always be free to make sure the unit doesn’t looses its
position.