Xilinx Zynq-7000 User Manual Download Page 341

Page: 341 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

341

UG586 November 30, 2016

www.xilinx.com

Chapter 2:

QDR II+ Memory Interface Solution

CQ_MAP

Bank and byte lane position

information for the read clocks

(CQ/CQ#). See the

K_MAP

description. This parameter varies

based on the pinout and should

not

be changed manually in

generated design.

See the

K_MAP

example.

ADD_MAP

Bank and byte lane position

information for the address. 12-bit

parameter provided per pin.
• [11:8] – Bank position. Values of

0, 1, or 2 are supported.

• [7:4] – Byte lane position within a

bank. Values of 0, 1, 2, or 3 are

supported.

• [3:0] – Bit position within a byte

lane. Values of [0, 1, 2, . . ., A, B]

are supported.

This parameter varies based on the

pinout and should

not

be changed

manually in generated design.

Upper-most Data Write/Data Read or

Address/Control byte group. The selected bank is

referred to as Bank 0 in the parameters notation.

Numbering of banks is 0, 1, and 2 from top to

bottom.
Byte groups T0, T1, T2, and T3 are numbered in

parameters as 3, 2, 1, and 0, respectively.

Bottom-most pin in a byte group is referred as ‘0’

in MAP parameters.
Bottom-most pin in a byte group is referred as ‘0’

in the MAP parameters. Numbering is counted

from 0 to 9 from the bottom-most pin to the top

pin within a byte group by excluding DQS I/Os.

DQS_N and DQS_P pins of a byte group are

numbered as A and B, respectively.
264'h000_000_239_238_237_236_23B_23A_235_2

34_233_232_231_230_229_228_227_226_22B_22

A_225_224: This parameter is denoted for an

Address width of 22 bits with 12 bits for each pin.

In this example, the Address width is 20 bits.

Ordering of parameters is from MSB to LSB (that

is, SA[0] corresponds to the 12 LSBs of the

parameter).
12'h224: Address pin placed in bank 2, byte lane

2, at location 4.
12'h11A: Address pin placed in bank 1, byte lane

1, at location A.

RD_MAP

Bank and byte lane position

information for the Read enable.

See the

ADD_MAP

description. This

parameter varies based on the

pinout and should

not

be changed

manually in generated design.

See the

ADD_MAP

example.

WR_MAP

Bank and byte lane position

information for the Write enable.

See the

ADD_MAP

description. This

parameter varies based on the

pinout and should

not

be changed

manually in generated design.

See the

ADD_MAP

example.

Table 2-13:

QDR II+ SRAM Memory Interface Solution Pinout Parameters

(Cont’d)

Parameter

Description

Example

Send Feedback

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands

Xilinx Zynq-7000, User Manual

Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands