Xilinx Zynq-7000 User Manual Download Page 340

Page: 340 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

340

UG586 November 30, 2016

www.xilinx.com

Chapter 2:

QDR II+ Memory Interface Solution

DATA_CTL_B0,

DATA_CTL_B1,

DATA_CTL_B2

Defines mode of use of byte lanes

in a given I/O bank. A 1 in a bit

position indicates a byte lane is

used for data, and a 0 indicates it is

used for address/control. This

parameter varies based on the

pinout and should

not

be changed

manually in generated design.

4'b1100: With respect to the BYTE_LANE

example, two byte lanes are used for Data and

one for Address/Control.

PHY_0_BITLANES,

PHY_1_BITLANES,

PHY_2_BITLANES

12-bit parameter per byte lane

used to determine which I/O

locations are used to generate the

necessary PHY structures. This

parameter is provided per bank.

Except for the CQ_P/CQ_N,

K_P/K_N, and DLL_OFF_N pins, all

Data Write, Data Read, and

Address/Control pins are

considered for this parameter

generation. This parameter varies

based on the pinout and should

not

be changed manually in

generated design.

This parameter denotes for all byte groups of a

selected bank. All 12 bits are denoted for a byte

lane and are ordered from MSB:LSB as

BA98_7654_3210. For example, this parameter is

48'hFFE_FFF_000_2FF for one bank.
12'hDF6 (12'b1101_1111_0110): Bit lines 0, 3, and

9 are not used; the rest of the bits are used.

BYTE_GROUP_TYPE_B0,

BYTE_GROUP_TYPE_B1,

BYTE_GROUP_TYPE_B2

Defines the byte lanes for a given

I/O bank as INPUT or OUTPUT. A 1

in a bit position indicates a byte

lane contains INPUT pins, and a 0

indicates byte lane contains

OUTPUT pins. This parameter varies

based on the pinout and should

not

be changed manually in

generated design.

4'b0110: Middle two byte lanes contain INPUT

pins, and the other byte lanes contain OUTPUT

pins.

K_MAP

Bank and byte lane position

information for write clocks (K/K#).

8-bit parameter provided per pair

of signals.
• [7:4] – Bank position. Values of 0,

1, or 2 are supported

• [3:0] – Byte lane position within a

bank. Values of 0, 1, 2, or 3 are

supported.

This parameter varies based on the

pinout and should

not

be changed

manually in generated design.

Upper-most Data Write/Data Read or

Address/Control byte group selected bank is

referred as Bank 0 in parameters notation.

Numbering of banks is 0, 1, and 2 from top to

bottom.
Byte groups T0, T1, T2, and T3 are numbered in

parameters as 3, 2, 1, and 0, respectively.
48'h00_00_00_00_03_13: This parameter is

denoted for 6 write clock pairs with 8 bits for

each clock pin. In this case, only two write clock

pairs are used. Ordering of parameters is from

MSB to LSB (that is, K[0]/ K#[0] corresponds to

the 8 LSBs of the parameter.
8'h13: K/K# placed in bank 1, byte lane 3.
8'h20: K/K# placed in bank 2, byte lane 0.

Table 2-13:

QDR II+ SRAM Memory Interface Solution Pinout Parameters

(Cont’d)

Parameter

Description

Example

Send Feedback

Summary of Contents for Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands

Xilinx Zynq-7000, User Manual

Search results

Summary of Contents for Zynq-7000

Reviews:

Related manuals for Zynq-7000

Brands by name

Popular brands